Jump to content
SAU Community

Recommended Posts

For Sale Got a 180sx shell that needs a new home as I don't have the time to give it work it needs.

It's a 1990 model minus the following;

- Front bar

- Motor (ca18det)

- Gearbox

- Diff

- Front Calipers

- exhaust & cooler

What it does come with;

- Bodykit (includes sideskirts and rear pods) not sure of brand but seen them before.

- faded leather interior (a clean and a hit of vinyl spray will bring it back to it's former red glory)

- Ca radiator

- Ca manual gearbox mount and tailshaft

- Paint I would describe as above average, I believe it does have 1 or 2 small scrapes down the drivers side which can get pics if needed, but definitely nothing major.

- Car wiring loom and gear is all there.

- suede steering wheel which needs a clean.

- Z32 Rotors

- Full rear brakes, lines and calipers/rotors

- Power Steering pump and lines still connected

- Brake and clutch master cylinders

Reason for sale

Originally purchased to build a drift pig, but could easily be put back on road by throwing a drivetrain into it as the car is full complied.

Price - $1750ono going cheap (no dreamers please, only enquire if you are interested, this is a great basis for a road or track car).

Location - Near Hornsby

Contact via PM for viewing, available most days after 5.30pm and on weekends, all by appointment.

Thanks

Pictures (I have more but photobucket is closed for maintenance at the moment, will post later)

DSC02715Medium.jpg

DSC02714Medium.jpg

DSC02724Medium.jpg

DSC02719Medium.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...