Jump to content
SAU Community

Recommended Posts

hi all

iam new to this and have imported my r34 few weeks ago. have been looking around for some new wheels and suspensions to make it handle better also maybe getting a little bit extra power gain. the car looks very standard except for the factory fitted sports exhaust whic looks and sounds grt.

now i know most of you will tell me to look at the previous thread and see what i would like done but all thats is to technical and knowing me i dont understand a lot of it.

so, need someone on here that can help me with advise.

this is what i have been thinking of doing...tell me if u disagree...

wheels

18inch

19inch - have been intersted in this

splitfire coils

suspensions - just to make the car handle better not going overboard

as for getting more power - it is my daily drive so nothing to extreme

thanks in advance everyone.....will look forward to getting some good advise and knowledge from all you experts

and also someone that could do al this in sydney west.

cheers

:/

Plenty of threads around for this!

basic mods for power

FMIC and Full exhaust.

then if you want more....

boost controller and ECU

then if you want more....

turbo, injectors, AFM, rebuilt motor

suspension...

sway bars front and rear

maybe a set of bilstein shocks and whiteline springs, or tein super street coilovers

so Id do..

FMIC and exhaust, tein super street and sway bars

car will perform alot better just with those basic mods :/

5k right there :P

Plenty of threads around for this!

basic mods for power

FMIC and Full exhaust.

then if you want more....

boost controller and ECU

then if you want more....

turbo, injectors, AFM, rebuilt motor

suspension...

sway bars front and rear

maybe a set of bilstein shocks and whiteline springs, or tein super street coilovers

so Id do..

FMIC and exhaust, tein super street and sway bars

car will perform alot better just with those basic mods :/

thanks mate....appreciated....any particular brands on intercooler and with exhaust...have been looking at xforce system turbo back(anygood)

A just jap FMIC kit is a good upgrade, cheap...but will work fine. I had one on my r33 which held 254rwkw no dramas!

www.justjap.com

yeah xforce is pretty common, cant go wrong with them

but Id look at full system, 3" front, 3" dump, (high flow cat isnt an issue if you dont upgrade, unless its fubared!) and 3" cat back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...