Jump to content
SAU Community

Recommended Posts

alright guys this might sound pretty retarted,but here it goes.IM looking to get a new exhaust system for my completely stock 34 i was wondering if anyone can give me info on wat i will need to look at buying,prices,websites where i can buy it from i will pay pretty decnt money for it too sound good without getting defected.also wat are your thoughts on those silencing exhausts???

thank you.

Link to comment
https://www.sau.com.au/forums/topic/283498-r34-exhaust/
Share on other sites

i just did a full custom exhaust on my NA r34,,,, which is pretty much ur only choice that im aware of if your car is 4 door and 4wd like mine,

i used,

-coby extractos 270$

-exhaust gasket, not genuine 45$

-2.5 inch mandrel bent pipe ~60$

-x-racing high flow stainless resonator 100$

-pro racing stainless high flow twin tip european style exhaust 150$

-removing old exhaust bending and installation labour was 450$

its as loud as F#$%!!! but they arent so strict on noise here, so you'll definately want a silenced exhaust or a multi core muffler installed before the actual exhaust and before the rear axle

ive found the 2.5 inch pipe to be good flow on the highway, no restriction on flow, but when cruising in town i think 2.25 would be a better diameter for the low rev range...

all those prices are in NZ dollars aswell, goodluck!!

Link to comment
https://www.sau.com.au/forums/topic/283498-r34-exhaust/#findComment-4769299
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...