Jump to content
SAU Community

Recommended Posts

Hey I had/have (not sure if it's still happening b/c I learned to drive in such a way it didn't happen) this problem with I bought my 33GTS-T

Basically if you just start getting on boost (>3200rpm or something) then put the clutch in the rev counter will fall all the way to 0 and your engine will die, is this right?

Two things you can do to to avoid the stalls:

- When you think your driving might cause this to happen, blip the throttle after you go into neutral/put the clutch in, and it'll stop the engine from dying

- If it does die and you're still rolling (even a little) just drop the clutch whilst in second gear and it'll force the engine to turn over and spring back to life.

Very annoying problem when I first got the car. A year later and it doesn't seem to happen anymore, but I'm not sure if that's because I just adjusted my driving to avoid it or in the 3x services between then they fixed it unknowingly.

yeah exactly my problem ae.. to the tee i got a 32 tho

umm yeah thats what ive been doing hey just dropping the clutch but i wanna try fix the problem..

i find it happens wen the engine is a bit cold so i warm it up befor i drive it but then sometimes just randomly wen i clutch it round a corning it will just die and the steering goes all hard so i just drop the clutch

not a clue wot could be causing it tho??

nah exactly like how i said it.

put the foot down every now and again usually its alright but sometimes wen i putt my foot down for a few seconds then hold the clutch for a bit its just dies.. reves drop from where ever its at at the time then drops to 0 and dies.

it happened once wen the engine was cold so i warm it up before i drive it but sitll does the same thing even wen i been driving for half an hour or so.

any ideas mate?

yup ive got a bov that isnt plumed into the air box or anything jsut straight into the atmosphere ..

what can i do to fix that? jut plumb it into the air box or wot?

The main issue is that the AFM is getting an incorrect signal due to the registered intake charge blowing off.

You need to use either a hybrid BOV which vents both to the atmo and recirculates (which still isn't a 100% fix) or replace the stock bypass valve and return the charge to the system after the AFM so it doesn't overfuel.

Yeah basically it is overfueling because the ECU is reading* air that isn't there.

On a side note, wtf are you clutching in around a corner? you should always go around corners in gear with clutch out.

Edited by bubba

This has just started happening on my car last night.

However the IDLE of my car is extremely rough. At idle, my car is missfiring that badly, it sounds like a 350 with the lumpiest possible cam it in. Yet while driving at anything above 1750RPM, it wont miss a beat.

Any ideas? I have read that it may be worth cleaning the AAC valve, however i do not believe that it is the coil packs or plugs, as if they were not funcitoning correctly, my car would missfire throughout the entire revrange. At idle, there is more resistance than while revving....

I have no idea why it wont idle properly/missfires like a b!tch....

Well it has been missfiring on idle for a few days last night, so i'm more concernced about that.

I have checked that, and all vacuum hoes are connected.....any other ideas lol?

Could it be my stock AFM is screwed?

New spark plugs went in about 1500-2000kms ago, copper plugs. Have always used NGK copper plugs (cant remember the code for the plug) and have never had any trouble.

AAC valve? Coil packs? Piston rings? I dont know what it could be >.<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...