Jump to content
SAU Community

Recommended Posts

Hey Guys.

Was working on my R33 GTS-T Series 2. Put in new plugs. and now the car has never run the same.

I replace the plugs as the car was unstabe under heavy throttle loads.

I put it back together and its running like a WRX.

After this tho....

I bought new CoilPacks, and new plugs again... and gapped them. and changed the fuel filter.

AND it is still running like a shitbucket wrx. tested crank angle sensor and engin compression ratio, and also fuel pressure.

Any Help.

Next step is to have a look at the injectors.

Any suggestions before i take my car to bits?????

Cheers,

Michael

Link to comment
https://www.sau.com.au/forums/topic/283965-skyline-sounds-like-a-wrx/
Share on other sites

yeah will do..

My mechanic mate has put more plugs in and tested them... but will get him to do it again.

So not fuel related.????

Even though it is running lean?

Keep coming with the suggestions :D

It's probably an ignition issue. Try swapping an ignitor with a buddy and see if that works. Also, what are you gaping the plugs to and what kind of coils are you running? Pull the cover off an pull the coil plugs off one at a time. the one that doesn't just about kill the motor and sounds the same is your problem cylinder.

Your car probably isn't actually running lean. If you don't have spark in one cylinder then air and fuel is just passing threw causing the wideband to read lean.

Hope that helps.

yeah will do..

My mechanic mate has put more plugs in and tested them... but will get him to do it again.

So not fuel related.????

Even though it is running lean?

Keep coming with the suggestions :down:

I have had new plugs that where stuffed straight out of the box, quite a few times over the years, but

Try testing the wiring loom for the coils, the loom for these that runs to coils is fairly straight foward to remove from car. I'd bet the loom has poor conections inside it and since you moved this to fit new plugs etc, its proberly upset the ageing factory wiring.

(note) it may test ok, have a look inside loom, I recently did on my gtr and found a real problem as there is a number of wire crimps, which I soldered and my car its now even more of a joy to drive than ever before. If you don't realy know how to solder best to get someone who knows what their doing as these wires are a bit thick at crimped area.

TIP don't just wrap in electrical tape use self alamagating tape, far better sealing properties but expensive. Jaycar have it.

Hope this helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...