Jump to content
SAU Community

Cheap Immobiliser?

SL33K

By SL33K,
in Western Australia

 Share

Recommended Posts

SL33K Experienced

SL33K

Posted
Posted (edited)

does anyone know where i can get a Cheap immobilser installed?

a very cheap one as i am planning on getting an expensive one soon when i get enough cash.

the problem is, i bought an r33 from a dealer and it was getting compliance done when i went to have a look at it and dint pay attention at immobiliser coz i was more interested in checking out the mechanical side of the car and body lol. i checked the whole car out and its perfect. only thing i realised is that it does not have immobilser and i am not sure what will happen when i take the transfer papers.

does anyone know where i can get a cheap one installed ASAP?

what happens if they noticed i havent got a immobilser installed? do i have to go through the pits or somethin after getting one installed?

cheers guyz

love u all :D

Edited by SL33K
Link to comment
https://www.sau.com.au/forums/topic/284045-cheap-immobiliser/
Share on other sites
syfon Veteran

syfon

Posted
Posted

As soon as you submit the transfer papers you will receive an "Immobiliser Offence" letter in the mail. You have 3months to get an immobiliser installed on the car, so don't stress you got plenty of time.

Then after you have had the immobiliser installed and filled in an "Immobiliser Statutory Declaration" form (link http://www.dpi.wa.gov.au/mediaFiles/lic_mr191.pdf), you will then receive the transfer invoice for payment of stamp duty.

As for who does the immobiliser installs i wouldnt have a clue :down: lol

syfon Veteran

syfon

Posted
Posted
go back to the dealer and ask him to install one...

its illegal to sell a car without one.

Did you get this from over East like you were mentioning a while ago?

Eastern States do no require an immobiliser, but here it is a legal requirement for sale and you can't go over the pits without one.

Both of you are wrong - it is not illegal to sell a vehicle in Western Australia without an immobiliser.

If the vehicle is less than 25 years old it must have an immobiliser fitted to it by law, however if for some reason it does not have an immobiliser, it is the PURCHASERS responsibility to install an immobiliser within 3 months of the vehicle being transferred into their name.

Vehicles 25years or older are exempt from having immobilisers and so are vehicles over 4.5 tone Gross Vehicle Mass aswell as Motorcycles.

I should know this, i work at with the Dept of Transport Licensing Services :down:

  • 1 year later...
Bizkit Contributor

Bizkit

Posted
Posted
Both of you are wrong - it is not illegal to sell a vehicle in Western Australia without an immobiliser.

If the vehicle is less than 25 years old it must have an immobiliser fitted to it by law, however if for some reason it does not have an immobiliser, it is the PURCHASERS responsibility to install an immobiliser within 3 months of the vehicle being transferred into their name.

Vehicles 25years or older are exempt from having immobilisers and so are vehicles over 4.5 tone Gross Vehicle Mass aswell as Motorcycles.

I should know this, i work at with the Dept of Transport Licensing Services :down:

Sorry for resurrecting an old topic. I'm going through the same process at the moment and wanted to know if these laws still apply. In other words, can i transfer the car into my name without an immobiliser and get one installed within 3 months later?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...