Jump to content
SAU Community

Recommended Posts

Hey guys!

Picked up my r34 skyline not long ago and its a non turbo but has a GTR wing on it.. I like it and I'm keeping it, but I also like upgrading car audio.

I've got a low power temporary sub sitting in the boot at the moment and from inside the car sounds good, but from the exterior it's a different story.

The bit where the wing mounts onto the boot is ever so slightly loose and can be shut up if I jam something under it as small as a folded piece of paper, but is there a way to just tighten it??

Also, the adjustable part of it has actually bowed slightly and sits heavily on the rest of the spoiler, but when I've got the bass pumping, even at low levels, this rattles like crazy (again, only audible from outside the car). Does it just need adjusting up or is there another way to get around this??

post-66189-1251798928_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/286096-spoiler-rattle/
Share on other sites

i had a similar problem, had water leaking in through the spoiler holes and massive rattles

i created some 'gasket' to sit between the boot and the spoiler,

out of rubber mat from bunnings, worked perfectly,

stopped water leak and supressed the rattle heaps

Link to comment
https://www.sau.com.au/forums/topic/286096-spoiler-rattle/#findComment-4801763
Share on other sites

i had a similar problem, had water leaking in through the spoiler holes and massive rattles

i created some 'gasket' to sit between the boot and the spoiler,

out of rubber mat from bunnings, worked perfectly,

stopped water leak and supressed the rattle heaps

had a similar problem with m r33 wing, i used the thick expensive clear 3m double sided tape underneath it to fix the problem

had it on my 32 as well (not from epic hektik subs - just noticed it at high speeds)

i removed the spoiler, discovered the water and rust

so i got a new boot with no spoiler holes :D

Link to comment
https://www.sau.com.au/forums/topic/286096-spoiler-rattle/#findComment-4802054
Share on other sites

how to tell if its a fake fibreglass copy?

well look under neath the wing where the stands bolt to the wing, it should be a plate with 2 screws, if theres no screws and the stands just go straight to the bottom of thewing then its a copy.

oem one has a plate that screws to the stands with 2x 10mm bolts and then that bolts to the bottom of the wing with 2 screws or so.

Link to comment
https://www.sau.com.au/forums/topic/286096-spoiler-rattle/#findComment-4821349
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...