Jump to content
SAU Community

TRACK DAY!!! Morgan Park Warwick 14th Dec!!!

WHITE R32

By WHITE R32,
in Queensland

 Share

Recommended Posts

WHITE R32 Grand Master

WHITE R32

Posted
Posted

hey guys.... as most of you know there is a circuit at warwick and its alot of fun.... some of us went to the last race day and for around $40 we had a SH!TLOAD of fun....

i think the next one is the 14th of december (sunday) im still trying to confirm this with the organisers... there is food out there (bbq) and drinks etc and its a really easy going atmosphere as those who attended will also say.... ill be debuing my r32 with its new setup hopefully (so thats reason in itself to attend :wassup: )...

but seriously its the best value for money event and the most fun you can have in ANY car not just a skyline.... any car would be fun out there.... fingers crossed my car will be all sorted and ready to rock and roll by then..... all you need is basically a roadworthy car,fuel and the money to enter.... you get heaps of track time probably too much really lol....

im in the middle of moving house at the moment so it may be a short while till i can get back on and confirm details/answer questions so perhaps slip or mick or jay or belgarion etc could help anyone out who asks questions so they get answers in a short time.... ;)

51jay Mentor

51jay

Posted
Posted

I posted this a few days ago, in the Queensland Events Forum, anyone going please e-mail or phone Ross as soon as you'r certain you'll actually turn up.

Dear Jay,

Please advise your members that they are welcome to come along to Warwick long circuit on 14th December.

The coast is $80 for the day starting at 8am going through to 5pm. Food and drinks will be on sale throughout the day.

We must know who is coming as we must have a minimum of 26 cars to cover costs. We have also have set a maximum of 50 cars so please advise those intending to come to contact me either by email or phone. Phone 46307292 or 0419667137.

Cheers Ross

--

Ross Horton

6/56 Mort Street, Toowoomba, Qld 4350

Phone: 07 46380746 Fax: 07 46380745

http://www.TAS-Performance.com.au/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      2001 R34DE

      By PranK · Posted

      R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...