Jump to content
SAU Community

Recommended Posts

Hey Guys, im new to this blogging thing and dont kno if i did it right.

well pretty much i have a R34 GTT 98 coupe, i have a Garret T28 Ball Bearing Turbo swapped from my cousin for a xbox 360 (he had 2 of them). i am wanting to change my stock turbo to put the T28 in for more response.

some ppl tell me that its a smaller turbo so there will be no high end power, but thats not what i want, i want response from the engine.

can you guys give me some insight of what i need and how to go about it? All he gave me was the turbo and actuator.

ps. also what size is the stock turbo on the r34 gtt? my stock boost gauge works and sometimes doesnt at all, but i still get the bov sound. any ideas?

thanks again and its good to be part of a community.

Link to comment
https://www.sau.com.au/forums/topic/287521-r34-gtt-turbo-help/
Share on other sites

I'd think that you'd need some form of ECU or Piggy Back ECU like a Power FC or S-AFCII to tune the car after the turbo install. Your tuner should then be able to get it to the state you're looking for.

As for the boost gauge issue; sounds like a faulty boost sensor, as it if were a leak then I would suspect it wouldn't work at all.. I've been told it is a common issue with R34 GT-T's.

thanks for the reply R34 Wong, yeh for the ECU side, i am goin to Nistune after the turbo install, but with the T28, do u think im being stupid or is it actually worth it?

i mean the T28 has only done 2000ks, and i dont think i want to spend more money on something that i already have.

if its a common failure, i can no longer blame the gauge, i thought the bastard had a personal vendetta against me.

thanks again

no problems mate. We'll, I guess it all depends on how far you want to take the car. The modification bug is a strong pull...

If you're not looking to go too far, I'd suggest something along the lines of an S-AFCII, as it will allow you to revert your car back to stock and flog it if you intend to down the line.

Also means you can sell the S-AFCII seperately or else transfer it across to your new car.

Good luck with your car mate, and welcome to SAU.

T28 off what?

If the flange is different - forget it. Simply not worth the effort. Overall i still think it's a waste of time/effort/money. If you don't like how responsive a R34 NEO is with a factory turbo, you need to go buy a V8 :P

If you want more response... Keeping the stock turbo

1. Exhaust.

2. Full tune/ECU, adjusting the VCT as well for response if you are that serious

3. Up the boost to 10psi or so

4. Decent flowing panel filter in the stock airbox

It will feel much nicer everywhere from takeoff to the top end. Stock ECU's are filthy.

im not exactly sure but will the stock turbo be ok to handle power? slappin myself if sound silly but would the usage of power snap the nylon part?

coz atm i got the blitz podfilter, turbo back exhaust with high flo cat, fmic. i was goin to get nistune to piggy back the ecu after a turbo upgrade, but if u think otherwise, i will follow suit.

unfortunately i just dont kno as much as i would like to, thanks for the help.

my car is back firin alot, i changed the sparkplugs to platinum, oil change and throttle body clean, maybe tunin the ecu will help?

thanks for the reply

Edited by Fei Jai

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...