Jump to content
SAU Community

Recommended Posts

taken from other sites

some 50+ cars attending apparently, wrxs skylines silvias

Jervis Bay cruise on the 7/12

8.30am Meet Hombush P6 8:30am to leave about 9am.

9:45: There is a large Area to the side of the road on the Hume Hwy at the Picton Turn off (just before the off ramp) that we will stop and wait for straglers (read Skylines ) that got caught in traffic coming out of the city. (good place for Penrith and southern people to meet here rather than drive all way to Homebush).

Continue down Hume Hwy to Moss Vale exit, turn left off Hume Highway and follow signs to Kangaroo Valley. Drive Through Kangaroo Valley and follow signs to Nowra. Through Nowra follow signs south to Jervis Bay and arrive at Huskison for lunch around 12 - 12:30pm

2pm: (or there abouts) Head back through Nowra amd head to Kiama (either the high road through Berry or Low road past 7 mile beach). Arive Kiama Blow Hole about 3:30pm for Poto opertunity (traffic will be fine at this stage).

4:30: Miss traffic bottle kneck by heading from Kiama through some twisty fun stuff through Jambaroo to Albion Park and head north to Wollongong and up the freeway to Sydney.

(Those that want to can take on Maqaurie pass at Albion Park and head back to MosVale and back up the Hume Hwy)

Homebush P6 is very easy to find as you just follow the signs once your at Homebush

And also as long as everyone understands that anything to silly, as in driving wise, wont be tolerated and they will be sent home or asked to leave the cruise hahaha last thing we want is the cruise ruined or any accidents involving our cars because of 1 or 2 idiots



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...