Jump to content
SAU Community

Defect Station On Boundary Rd !


Recommended Posts

Be Warn,

The usual defect station on Boundary Rd near Lower Dandy road is now pulling cars over. They used to target Trucks only but they now must have gotten bored and start pulling cars over as well.

I just got pulled over and almost got a big fine if it wasn't for this TOP COP.

I was driving my sister's car, the rego just expired (1 day), there is slightly camber wear on the inner wall of the tyre. This young COP was ready to book me then the old fella said nah, don't worry i wouldn't do it. The old fella then told me he's letting me go this time but he wouldn't like to see the car again under the same condition.

Mind you i was going to explain but i didn't need to anyway, the rego is PAID i just haven't been bother sticking it on, the tyre was worn but very very lightly.

Hats off to you Sir, its people like you that make us change our attitude toward the law enforcement !!!

Link to comment
https://www.sau.com.au/forums/topic/288223-defect-station-on-boundary-rd/
Share on other sites

Mate I would do a check and if car unreg even 1 day. I would issue a fine it's one of the few things we have NO leaniency with. Unreg= No TAC/INS coverage. If it was paid fair enough. I really couldn't care about issuing defects unless car in really bad/dangerous way or owned by known crooks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, it's me! Though honestly, if I had 20M in my bank account tomorrow, I would not want to be rid of my car all of the sudden - Which makes me think this is money stuff, not "I actually hate car" stuff. I'd probably double down and buy even more trinkets and fun things for it. If this is not you, then sell it cheaper. It will sell at a certain price after all.
    • This is the LCA mount reloctaion kit. Self explanatory in its description. https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=62&_fid=1e812d392&_ss=c These are the alloy subframe bush inserts that I am using. I like them. https://au.gktech.com/products/rear-subframe-slip-in-collars?_pos=29&_fid=1e812d392&_ss=c Alternatively, if you have original and shitty bushes, you might consider outright replacement with poly. https://au.gktech.com/products/polyurethane-rear-subframe-bushes?_pos=28&_fid=1e812d392&_ss=c I would also higly recommend that you look into adjustable RUCAs and tension rods, so you can sort out the camber and bump steer behaviour, especially if the car will be any more than ~15mm lower than stock. I would also highly recommend the GKTech FUCAs, although you really should do some research and learning on the subjetc of R32 FUCAs before making any decisions. All of this will be criticaly difficult to get through a TÜV inspection too, if that happens to be relevant to you. Note that if you do install the relocation kit, you will absolutely have to replace the associated bushes with spherical joints (you can read all about that on the product page) or upgrade the LCAs also.
    • I picked up my block and head last week and have been slowly assembling it since then. Pictures I took earlier this week. The rest of the auxiliaries are on now. I just have my intake manifold runners to tap for my WMI direct port setup before putting it back on. I should hopefully have the motor back in by this weekend.   
×
×
  • Create New...