Jump to content
SAU Community

Recommended Posts

i just wanted to see how are you guys going with your rotors , i guess everyone had them bed in by now

what pads are best for these?

anybody run them on track cars?

how did everyone go with orientation of rotors , i know there's left and right on boxes but would this link be right way to do it?

http://www.dba.com.au/2006/QnA/DBA_QnA_22.asp

if anyone has pictures please do post

cheers

Link to comment
https://www.sau.com.au/forums/topic/289023-r33-rda-slotted-rotors/
Share on other sites

i can check the orientation when i get home if you want, i have ran Endless SSS and Racebrakes RB74 with mine, prefer the RB74 (I have used many pads, but only those two on RDA slotted rotors)

Orientation of RDA slotted rotors makes absolutely no difference what so ever as their internal veins are straight...

that explains it , i followed the markings on rda's box and they appear to be same way as on dba site so i guess there's no wrong or right way to put them on.

btw im using qfm HP-X that i got from GLS Rallysport and they are great so far (still bedding in rotors so babying it for another 150km or so)

that explains it , i followed the markings on rda's box and they appear to be same way as on dba site so i guess there's no wrong or right way to put them on.

btw im using qfm HP-X that i got from GLS Rallysport and they are great so far (still bedding in rotors so babying it for another 150km or so)

The only time rotors can be on right or wrong is when the internal veins are directional, in which case it's VERY important they're on the right way!!!

DBA, RDA and most other cheap brands might specify a direction on the box, but it will make 3/8 SFA difference because the internal veins are straight.

Ironically enough, most of the big end of town rotors (Brembo, AP etc.) which do have directional internal veins, will actually have the external slots the opposite of what DBA and RDA specify...

r33 rda's on the front and rear here

heaps of track work (7'ish days)

3 sets of trw on the front

1 set of qfm on the front

close enough to no wear on the rotor (though they have surface marking)

2 sets of trw on the rear

1 set of qfm on the rear

close enough to no wear

qfm are worth the extra $$ over the trw. trw were good but has all the bite at the end of the pedal and in the last 50m, and faded after 3 laps.

qfm has better initial bite and don't fade, they feel harder if you know wat i mean.

there wasnt enough brakes for me. uas caliper spacers and 324mm dba rotors now. testing this weekend.

same set of qfm's and rda rotors on the rear and onto second set of qfms now with some air ducting on the front.

there wasnt enough brakes for me. uas caliper spacers and 324mm dba rotors now. testing this weekend.

same set of qfm's and rda rotors on the rear and onto second set of qfms now with some air ducting on the front.

Also keep in mind guys that there are compounds above A1RM in the QFM range, but these do start to become track only pads. Comp 6,7,8,9,12,15 etc...

Also keep in mind guys that there are compounds above A1RM in the QFM range, but these do start to become track only pads. Comp 6,7,8,9,12,15 etc...

Do you have more info on these? It might be worth advertising them on here...

I ran a set of Hawk Blue Track pads at the last Oran Park Day. They worked great but did put a very slight lip on my brand new rotors - I think any serious track pad would. Lots o stopping power there. I couldn't believe how solid the pedal feel was with this combo - totally different feel to a stock pad.

Now I have EBC Reds in (the ones I glazed at Wakefield Park after a 12 minute session). They don't have much initial bite now, but pull up ok at the bottom of the pedal - but the feel is so much squishy-er than the Hawks.

Oh, and the Hawk/RDA combo went a full 15 minute session with 0 fade.

I have rda on my 33, i would reccommend dba due to the fact that they paint the non pad surface area, all rdas will rust in this area and dont look the best from close up

Only other difference is that rda slots go all the way to the end of the rotor, where dba slots stop short of the end of the rotor, not very significant in my opinion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...