Jump to content
SAU Community

Oils And Oil Pressure

=STEVE=

By =STEVE=,
in Queensland

 Share

Recommended Posts

=STEVE= Apprentice

=STEVE=

Posted
Posted

hey everyone,

I have only just recently become a 32 owner and already have a few questions if anyone could help.

I've just done an oil change from Royal purple to Motul 4100 turbolight.

They both have the same viscosity range (10w40).

After the change i noticed that my oil pressure is low on idle after driving. Pretty close to zero in fact.

When up in the revs (say 3000 to 4000 revs) the pressure needle doesnt get much higher than 2kg/cm^2

The royal purple that was in it also did the same thing. But the royal purple wasnt very nice to the motor on cold start up, in that i could hear ticking.

So my question..... Is this a normal reading for oil pressure on the RB20??

cheers,

steve

Link to comment
https://www.sau.com.au/forums/topic/289473-oils-and-oil-pressure/
Share on other sites
mosquitocoils Veteran

mosquitocoils

Posted
Posted (edited)

Check the link in my sig

EDIT: Just had another look, doesn't have RB20det in there but you get a good idea from it.

Your pressure seems a bit low, but I'd get a sandwich plate on your oil filter and run an aftermarket oil pressure guage from it before you start freaking out, just in case.

Edited by mosquitocoils
Parag0n Mentor

Parag0n

Posted
Posted
Check the link in my sig

EDIT: Just had another look, doesn't have RB20det in there but you get a good idea from it.

Your pressure seems a bit low, but I'd get a sandwich plate on your oil filter and run an aftermarket oil pressure guage from it before you start freaking out, just in case.

Sandwich plate to the oil filter are terrible.

If you want an accurate reading mount it in the sump.

The Dan Grand Master

The Dan

Posted
Posted

Chances are that the oil pressure is fine. The factory sender is known, and well documented, to be problematic. Get yourself a manual pressure gauge or take it to a mechanic for a pressure test.

Sandwich plate is not necessary as you can just mount it in the same place the factory one goes.

If you want to replace the factory one, they are approx $210 from Nissan.

The Dan Grand Master

The Dan

Posted
Posted
a mobil 1 fully syn product what else ?

Royal Purple R&D their product and and the 10w40 has a higher film strength than Mobil1 also.

None of which has anything to do with his pressure. His brand of oil is not the problem.

32_Dave Mentor

32_Dave

Posted
Posted
Royal Purple R&D their product and and the 10w40 has a higher film strength than Mobil1 also.

None of which has anything to do with his pressure. His brand of oil is not the problem.

i know that, just wanted to see if anyone got protective of an inferior product.

Parag0n Mentor

Parag0n

Posted
Posted
Lol. Are you being serious?

How are you supposed to get an oil pressure reading from the sump?

You're 100 right, I got my pressure and temps mixed up, sorry.

But yes a sandwich plate will be less accurate for TEMPS not pressure, again must of been drunk when i posted that :laugh:

MountainRunner Mentor

MountainRunner

Posted
Posted

A sandwich plate is fine for oil temp as most of them have the end of the sensor in the oil flow, its only a problem when there is no flow over the sensor. Take a look at the data sheet of a typical temp sensor and they are accurate to 5% anyway, this will be the biggest source of inaccuracy unless you calibrate your sensor before installation.

I agree the nissan pressure sensor is very unreliable when old. A new one or aftermarket sensor is the way to go.

Motul oils are the goods. Plenty of track cars run them without any problems. Look at Nissan racing cars and you will usually see Motul stickers on the side.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
A sandwich plate is fine for oil temp as most of them have the end of the sensor in the oil flow, its only a problem when there is no flow over the sensor. Take a look at the data sheet of a typical temp sensor and they are accurate to 5% anyway, this will be the biggest source of inaccuracy unless you calibrate your sensor before installation.

I agree the nissan pressure sensor is very unreliable when old. A new one or aftermarket sensor is the way to go.

Motul oils are the goods. Plenty of track cars run them without any problems. Look at Nissan racing cars and you will usually see Motul stickers on the side.

comes back to the old saying..."if you don't want to spin a bearing...put Motul in it"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...