Jump to content
SAU Community

R33 Gtst Rb 26 Built Motor

adam Foster
 Share

Recommended Posts

adam Foster Mentor

adam Foster

Posted
Posted

I have a 1993 r33 s1 gtst for sale was my project for track/drift car.

Motor is an rb26 with gtst gearbox. engine was fully rebuilt from sep 08 through till January done around 3000 km since. The rb26 is out of a r32 gtr but has the r33 crank for the longer snout for oil pump drive.Rebuild included forged pistons and rods, arp head studs, new n1 oil and water pump, ACL racing Bearings. block was decked and machined. head was fully serviced machined and valves reseated. Bottom end ballanced metal head gasket. Recipts for work done.

car has coilovers, big y pipe, walllbro 500hp fuel pump i think it is. SARD fuel reg. gtr dash.

Has standard turbos. body is Straight but needs attention

$7500 FIRM as it sits has out of rego sep 23. 2009 pink slip on 20.9.09 still has few weeks left

can be contacted on 0411672105

post-52687-1254466303_thumb.jpg

post-52687-1254466400_thumb.jpg

post-52687-1254466435_thumb.jpg

post-52687-1254466490_thumb.jpg

post-52687-1254466533_thumb.jpg

post-52687-1254466598_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/290330-r33-gtst-rb-26-built-motor/
Share on other sites
Shazbanger Community Regular

Shazbanger

Posted
Posted (edited)

Hey mate, couple of questions for ya.

1) Is it engineered for the RB26?

2) If not, is the RB26 engine number on the rego papers?

3) Does the car have any mechanical faults whatsoever?

4) Will it pass rego with a new front bar?

5) Receipts for engine build? (Sorry, just re-read and says you do)

Cheers mate.

Edited by XS80ST
adam Foster Mentor

adam Foster

Posted
  • Author
Posted

The engine numbers off the 26 are on the rego papers but no engineer cert wasnt required. car has CURRENT PINK SLIP just need to pay the rego

mrsparkle Enthusiast

mrsparkle

Posted
Posted

hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

adam Foster Mentor

adam Foster

Posted
  • Author
Posted
hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

yer it is regoed with the 26 in it insurance didnt mind as long as it was on the papers. its killing my not getting a hit on the car at this price rebuilt cost me total around 8k and brought the car for 13k just befor the rebuild

adam Foster Mentor

adam Foster

Posted
  • Author
Posted

front bars in the bin lol was big low fibaglass bar and got all cracked from bush driveway. i havnt had and accidents but passanger side was in under coat when i broght it guy i got it off said it was scraped car is pretty straight. had different front fenders on the car thats why they are different colour. will throw in fibagrass wide front fenders

sIIgtst Rising Star

sIIgtst

Posted
Posted (edited)

hey.. just a few questions..

what engine management is the car running?

internal or external fuel pump?

any problems with the interior?

Cheers,

Corey

Edited by sIIgtst
weeman1 Collaborator

weeman1

Posted
Posted
Sorry guys hour north of sydney. Central Coast. if anyones keen on just motor or parts let me know

hey mate, where abouts on the coast are you? im at the entrance. id be interested in just the engine maybe as i need to rebuild mine so this would be perfect for me

adam Foster Mentor

adam Foster

Posted
  • Author
Posted

Sorry mate no swaps. $12,500 and its yours lol. Car is geniune, im just after a quick sale. Need $$$ and people just want to negotiate prices.

too cheap! put the price up , then it will sell :rant: . i didn't read your advert properly but i'm assuming no swaps?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...