Jump to content
SAU Community

Recommended Posts

I have a 1993 r33 s1 gtst for sale was my project for track/drift car.

Motor is an rb26 with gtst gearbox. engine was fully rebuilt from sep 08 through till January done around 3000 km since. The rb26 is out of a r32 gtr but has the r33 crank for the longer snout for oil pump drive.Rebuild included forged pistons and rods, arp head studs, new n1 oil and water pump, ACL racing Bearings. block was decked and machined. head was fully serviced machined and valves reseated. Bottom end ballanced metal head gasket. Recipts for work done.

car has coilovers, big y pipe, walllbro 500hp fuel pump i think it is. SARD fuel reg. gtr dash.

Has standard turbos. body is Straight but needs attention

$7500 FIRM as it sits has out of rego sep 23. 2009 pink slip on 20.9.09 still has few weeks left

can be contacted on 0411672105

post-52687-1254466303_thumb.jpg

post-52687-1254466400_thumb.jpg

post-52687-1254466435_thumb.jpg

post-52687-1254466490_thumb.jpg

post-52687-1254466533_thumb.jpg

post-52687-1254466598_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/290330-r33-gtst-rb-26-built-motor/
Share on other sites

Hey mate, couple of questions for ya.

1) Is it engineered for the RB26?

2) If not, is the RB26 engine number on the rego papers?

3) Does the car have any mechanical faults whatsoever?

4) Will it pass rego with a new front bar?

5) Receipts for engine build? (Sorry, just re-read and says you do)

Cheers mate.

Edited by XS80ST

The engine numbers off the 26 are on the rego papers but no engineer cert wasnt required. car has CURRENT PINK SLIP just need to pay the rego

hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

yer it is regoed with the 26 in it insurance didnt mind as long as it was on the papers. its killing my not getting a hit on the car at this price rebuilt cost me total around 8k and brought the car for 13k just befor the rebuild

front bars in the bin lol was big low fibaglass bar and got all cracked from bush driveway. i havnt had and accidents but passanger side was in under coat when i broght it guy i got it off said it was scraped car is pretty straight. had different front fenders on the car thats why they are different colour. will throw in fibagrass wide front fenders

hey.. just a few questions..

what engine management is the car running?

internal or external fuel pump?

any problems with the interior?

Cheers,

Corey

Edited by sIIgtst
Sorry guys hour north of sydney. Central Coast. if anyones keen on just motor or parts let me know

hey mate, where abouts on the coast are you? im at the entrance. id be interested in just the engine maybe as i need to rebuild mine so this would be perfect for me

Sorry mate no swaps. $12,500 and its yours lol. Car is geniune, im just after a quick sale. Need $$$ and people just want to negotiate prices.

too cheap! put the price up , then it will sell :rant: . i didn't read your advert properly but i'm assuming no swaps?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...