Jump to content
SAU Community

Recommended Posts

So I recently bought a S1 R33 Gtst. First thing I did was take it for a wheel alignment as it was pulling left considerably.

Everything was adjusted fine, apart from the front right camber is at -3.4 degrees or so.

I can't see anything obviously bent. Without pulling all the arms out and comparing side to side, are there some measurements I should be taking?

If its a case of throwing a pair of adjustable upper arms on, are the Cusco items the ones to go for? Would the Just Jap ones be worth considering, given that this car is my daily driver?

Link to comment
https://www.sau.com.au/forums/topic/291594-r33-front-camber/
Share on other sites

two kits? i thought it was closer to 2deg, that might be R32 though... i know my stagea has ~ -1.5deg from one kit same as the 33 kit

noltec make an arm with bushed ends IIRC... that would be my next choice

-3.4 is heaps on stock bushes....

how low is it? from guard to center of hub.

mine is too low atm, 340mm, which should mean that i've got camber on tap. but -2.5 is my max with pedders camber bolts.

im running -2 on a track based setup.

is there a way to adjust stock front camber? i get pretty bad inner tire wear on both fronts, (backs are perfectly fine)..

or do i need a adjustable camber kit? i need to either bring the bottom of the wheel in or push the top of the wheel out.

my radius rod bushes are gone, which im replacing, so might that contribute to it?

wow that is alot of camber.

I had -4 in my r33 but I had modified front lower arms which pushed it to -4 with whiteline camber bushes.

beforte that I could get JUST to -2

Something may be bent down there...or perhaps previous owner did something like I had :P

Yeh, something is not right at all. Had a quick look before, but couldn't see much. I need to get the tape measure out before I start buying arms i think :P

If the previous owner did do something, they were pretty dumb to only to it to one side :)

  • 1 month later...

So I think I have this problem figured out.

I measured all the arms, and none of them are bent. What is bent though is the front bolt holding the upper control arm to the car.

Hopefully replacing this bolt and getting a set of the whiteline eccentric bushes should sort out my problems :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...