Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

im in melb i can come pick it up also need the glove box front sway bar heater core unit inside the dash all the carpet boot trimming charcoal canister and air box and snorkel and drive window switch no 0403011187 thanks mate really need all these things

Hi, have you still got your tail lights?

Where can i pick them up?

Thanks DAnnie

so i have decided to wreck my r33 instead of fixing it after crashing it. everything for sale is in good condition unless stated otherwise. listed below is everything i can think of but if you need something not listed pm me or call on 0400119068. all interior parts are ready now (12/10) and will have things like motor and gearbox out by the end of the week. i will post pics up on request. feel free to make an offer but im not in a hurry to sell so dont bother low balling!! cheers, Shane

gcg turbo- sold pending payment

engine (inluding front facing plenum)-1300

gearbox-1500

front brake set up (rotors and callipers)-350

back brake set up-150

front subframe-250

steering rack-100

apexi coilovers (adjustable damper)-550

rear subframe + diff (shimmed)-500

front seats-200

rear seat-50

pedals-50

passenger door-120

drivers door (panel damaged, good for window and interior)-70

spare driver door (bought it to fix the car)-100

spoiler and boot-200

seat belts-100 the lot

s2 head lights. (2x left and 1x right)-250 each

fuel tank-50

tailshaft-100

heavy duty clutch and flywheel-100

brake master cylinder/booster-100

front 1/4 panels-120 each

side skirts (right side one slighty damaged)-50

white line swaybar-200

full exhausted system including front+dump pipe, high flow cat-500

big injectors-300

split fire coil pack-300

roll cage (half cage with side intrusion bars made by brown davis)-1000

17inch g-max rims (no tyres)-500

loom-100

tail lights-60

starter motor-40

defi water temp and oil temp gauge + defi control unit (missing oil temp sensor)-400

speedo cluster with 106k on the clock-150

would you have the round thin plate with a wire ribbon that sits behind the steering wheel that plugs into the airbag computer is about 2 or 3 mil thick and about 100 mil across is black with yellow info sticker on it if you have how much with postage to tassie thanks you can contact me on 0408802254 or pm on here your call

  • 2 weeks later...

Ill take the seat belts if they aren't already gone. Id also like some interior trim (handbrake boot, gearstick boot, carmats...) you name your price

  • 2 months later...

hey mate

i am after a piping that goes from the ic piping to somwhere (i dont know) near the stock bov.....

here is what i am after

post-37912-1268351673_thumb.jpg

if you have it them pm me please

  • 3 weeks later...

Hey mate i know its an old post,

But just wondering if u hav any of these parts i need??

- Frount passenger side quater panel

- The inner Frount gard Lh side were the cooler piping

goes thro and were the head light bolts up

i need that whole section

- S2 LH side, headlight

- Radiator suport bar

- frount reo bar, infrount of cooler

Any help would be much appreciated

if u hav any of the above send us a msg on 0403 236 931

cheers troy..

  • 2 months later...

im after the Heater AirFlow Direction Mode Actuator (underneath the dash passanger side above centre heater box) & a Heater Temperature Mode Actuator (driverside on the heater box pedal lil black box)..

if u got both of the PM me plz with a price from them..

cheers,

Robbie

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...