Jump to content
SAU Community

Recommended Posts

Just got the car a couple of weeks ago. At first it only seemed to make the sound when the car was cold, and as soon as i had reversed out the driveway it stopped. Now it seems to be making the sound whenever i push the clutch in and are changing between 1st, 2nd and 3rd gears. Weirdest thing is that it doesn't make the sound all the time just sometimes. Theirs also a burning smell if you jump out the car after driving. As for describing the sound its like a dull squealing, not particularly loud or anything. Also sound stops when you engage a gear.

Anyway if you guys have any ideas at all or could just confirm that's it going to be something that's not too expensive to fix that would be awesome.

Link to comment
https://www.sau.com.au/forums/topic/292484-bad-noise-when-the-clutch-is-in/
Share on other sites

Sounds like your throwout bearing. Depends how bad the sound is, my old S13 used to have a noisy bearing but went away when it was warm . Take it to your mechanic, you may as well upgrade your clutch cos you would be looking at the same labour(just read Burning smell. is your clutch slipping)

I have the same sound too everytime my clutch is in, but the sound is worst especially on gear 2. I guess thats just the clutch burning a bit but anyways its good if you replace your clutch every year to ensure it wont burn aheheh

How long is a piece of string?

Noise will usually get worse and worse before the thing shits itself. If it's just a dull whine for now then you might be safe for a couple thousand km but realistically it can collapse anytime it pleases. Leave it too long and you might start damaging the hydraulic release.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Why not? Since mines been built, I've used low boost maybe 5 times.
    • Yeah, so widen your search to any Nissan speedo first, then go wider if needed. I will say though, that there is a better than even chance that what I said first will likely come into play. They quite possibly won't come apart without damage. I tried to disassemble a stepper gauge that I wanted to repair. There was no way that needle was coming off the spindle, and I could not see how the spindle would come out of the mechanism behind. Assembled once, never to be disassembled, was my conclusion. Could be the same on the R34 cluster. Failing that - take the cluster to a workshop that specialises in automotive instrument work. There's usually at least one in every Australian city. They'll either be able to do it for you for small cost, or tell you it can't be done. It might be that "it can't be done" unless you follow some arcane procedure, including trickiness to glue it back together or something, that only experienced techs know.
    • Well, given that I, an engineer, almost never bring out the torque wrench to tighten up chassis bolts, despite fully knowing the theory, and instead rely on feel, which I happen to know is exactly how the majority of mechanics do things, should tell you the level of actual peril that exists from not achieving exactly 88 Nm of torque. How about if I just say then that 88Nm is at the lower end of the correct wheel nut torque range? Everyone knows how to tighten a wheel nut, right? And almost no-one ever brings out the torque wrench for that task
    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
×
×
  • Create New...