Jump to content
SAU Community

Recommended Posts

hey guys,

I was wondering if anyone would have any ideas where my car might be vibrating from.

Its an r32 4 door with hicas removed, and some kind of aftermarket gearbox mount apparently.

When Im driving the whole car seems to vibrate, it gets worse at some speeds than others. Like at 60km/h its worse than at 80km/h.

Before I removed the hicas there was about 5mm play in the rear wheels, I thought that was the problem. But now its all fixed and the vibration has only been recused a little bit.

Would the gearbox mount cause the vibration? Even while rolling in neutral at speed?

Link to comment
https://www.sau.com.au/forums/topic/292615-weird-vibration/
Share on other sites

If your rolling in neutral with the noise happening then i doubt it has anything to do with the drive train.

A few things to check are;

1) Toe alignment on the rear wheels

2) Wheel bearings

3) Have you been "practising" hand brake turns or had to lock up the tyres? Flat spots in the tyres can cause this unwanted vibration and noise.

I would think that the solid gearbox mount would on help transmit the vibration issue further through the car as it is solid, but if your saying that you get the vibration even when coasting in neutral, i'd start from the ground and work backwards.

Hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/292615-weird-vibration/#findComment-4891625
Share on other sites

Well the rear toe is all good. I only just had an alignment. Ill check to make sure nothing else has play in it though.

It occurs on other tires too, so they cant be the problem.

It feels like its coming from the middle of the car, so maybe tailshaft or soemthing? Though its hard to tell from the drivers seat lol.

Anyone had extra vibration from a solid gearbox mount?

Link to comment
https://www.sau.com.au/forums/topic/292615-weird-vibration/#findComment-4892430
Share on other sites

defo sounds like a uni joint problem mate.

take the tailshaft out and feel and inspect all the uni's by hand for any looseness and notching problems.

the solid mount will transfer more vibration but it will be a constant noise as the revs increase. not the sort of thing you are describing

Link to comment
https://www.sau.com.au/forums/topic/292615-weird-vibration/#findComment-4892458
Share on other sites

ahh ok, ill have a look at that when i get a chance.

I just checked and the rear wheels for play and they are perfect. Yay for getting rid of hicas!

But the front has a bit of play, so new tie rods and ends would help.

The one thing i did notice was that one of the rear wheels doesnt have any weights on it. Im pretty sure none of the factory wheels were perfect, so maybe i should get that checked out too...

Link to comment
https://www.sau.com.au/forums/topic/292615-weird-vibration/#findComment-4892464
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
    • Such a cool collection of cars back then.  
    • Mystery solved, thanks bro Bit of a strange mix, but i dont mind it, still looks good. 
    • nah no problems with bearings or hubs.  just the water pump leak and my AC death
×
×
  • Create New...