Jump to content
SAU Community

'Boost Worx' JZA70 Supra runs 10.8 @ 125+

whatsisname

By whatsisname,
in South Australia

 Share

Recommended Posts

whatsisname Grand Master

whatsisname

Posted
Posted

I headed down to AIR tonight (06Dec) to lend a hand to Shaun, Ben & co as they were running the 'Boost Worx' backed yellow 2JZGTE powered Supra (ex-RPM car).

Ben ran a string of low 11's @ over 127mph before finally getting the car to run closer to its potential with a PB of 10.8 @ 125+. The mph was down on the earlier passes as an IC hose blew off going into 3rd gear. The car should run closer to 10.4 with a few more tweaks.

All passes were on ET Streets (DOT approved) I'm not sure if they qualify for the HPI Street Drag Challenge or not?

I'm sure most will agree that the 2JZGTE is an awesome engine. Ben's Supra runs a dead stock internals 2JZ.

Another car worth mentioning was the factory standard new 3.5L V6 Magna (base model) whose female driver ran back to back 14.8 - 14.7 mid 90mph passes (best of 14.7 @ 96mph). The only mod was a slight change to the air box feed.

Link to comment
https://www.sau.com.au/forums/topic/29343-boost-worx-jza70-supra-runs-108-125/
Share on other sites
whatsisname Grand Master

whatsisname

Posted
  • Author
Posted

Yeah mate sure have!

I remember reading articles on the MKIV JZA80 Supra when it was first released in Japan. It was my #1 choice when I got interested in imports back in the early-mid 90's. They were a touch too expensive back then though :) Hence I got the Skyline instead. I've gone too far with the GTS to start again now :)

whatsisname Grand Master

whatsisname

Posted
  • Author
Posted

Hip,

Brand new ET Streets & a good suspension aligning session made a huge improvement on the strip.

ET Streets are a drag radial tyre made by Mickey Thompson. They're DOT approved which technically makes them street legal.

mickeyt.gif

"There's a simple way of identifying whether or not a tyre is legal for road use. If it has "DOT" or "E" written on the sidewall, it's passable - no probs. DOT is the US abbreviation for the Department of Transport, while "E" is the recognised European compliance symbol. Having said that, it wouldn't be unthinkable to get pulled over by the police for supposedly "bald tyres" - regardless of their technical legality."

The car is with Boost Worx now as the mechanic linked with the car moved from RPM to set up his own workshop. So the car moved with him.

Tim,

I'd say traction would've been a huge factor in who hosed who on the street! Neither cars have/had a lot of traction on road rubber. Ben mentioned turning the tyres @ 180+ on the road.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • PranK
      2001 R34DE

      By PranK · Posted

      Bloody apprentices! 🙄
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
    • GTSBoy
      Valve clearance for RB25det series 2

      By GTSBoy · Posted

      Keeping in mind that for most people this is a week to month long job!
    • Duncan
      Valve clearance for RB25det series 2

      By Duncan · Posted

      Its also worth mentioning that 30 years after it left the factory and god knows how many missed oil changes since, there is every possibility that one or more lifters are ticking because they are sticky/gummed up. To resolve that you need to pull the cams then pull each lifter, disassemble, clean, reassemble, soak in oil and re-install, and they should come up good as new.
×
×
  • Create New...