Jump to content
SAU Community

R33 Passanger Door, Diff, Kyb Suspension, 1/2 Shafts

Brokenz
 Share

Recommended Posts

Brokenz Community Regular

Brokenz

Posted
Posted

White Door with Glass and Motor, No Trim $40

Good LSD Diff from 1995 Model Non ABS $200

R33 GTSt Suspension. Std Struts with KYB Shocks $150

Silver Stock Plastic S1 Grill $50

Factory GTR Style Mesh Grill from Series 1.5 GTSt $150 (Cost me $150 used from Japan)

The plastic coating is coming away from the mesh so the mesh will need respray

Clutch Fan $80

Coil Pack Harness (Series II Motor) $50

5 x Series 1 Rb25det Spitfire Coil Packs (Also Good for CA18) $220

Series I AFM $20 (Not sure of its condition) Think it ran rough when raining but was fine when dry.

Series II AFM $120 Works fine

1/2 Shafts (From diff to wheels) $50

ABS Pump $20

Steering Column with Steering Wheel. Airbag not included $20

3" Catback Exhaust with 5" Genie Muffler $150

Centre Caps 3 x R32 and 3 x R34 GTSt Factory Alloys. $10 Each for 3 for $20

Parts can be picked up from Upper Mount Gravatt, Brisbane

Link to comment
Share on other sites
  • 2 weeks later...
Brokenz Community Regular

Brokenz

Posted
  • Author
Posted

Heres a pictute of the Grill. A couple of the clips will need to be glued back on as the have broken off in transit from Japan

Ans also a pic of the suspension. It was removed a couple of weeks ago when new KTS Coilovers where fitted

post-47634-1257725926_thumb.jpg

post-47634-1257726056_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LjB123
      R34 Series 1 And 2 Front Reo Difference?

      By LjB123 · Posted

      Awesome to know. I have a Series 1, and When pulling my front bumper off for the first time i realised my reo/crash bar was a bit worse for wear, and was going to try pick up a better one soon just so i can replace it. Someone is selling a full series 2 front bar and brackets for a decent price, so was going to probably reuse my brackets and install the new second hand reo/crash bar. I also have a genuine Altia body kit to do up, spray and put on, and not sure if that will use the series 1 or series 2 brackets for the front bumper, so having both will be handy, and knowing i can drill holes out to make stuff fit between series is also handy to know!
    • Kinkstaah
      R34 Series 1 And 2 Front Reo Difference?

      By Kinkstaah · Posted

      I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work. The center headlight brackets however, cannot. This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different. So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.
    • dbm7
      forum.r31skylineclub.com down or gone?

      By dbm7 · Posted

      Indeed  😃  Appears the site is back up now (migrated not updated) - kudos @funkymonkey & @PranK
    • GTSBoy
      rb20de neo +t conversion - boost pressure sensor needed?

      By GTSBoy · Posted

      If this, then this You can't really get away without it. There are hacks that you can do in Nistune, but things are much easier with the sensor than without it. If you're not planning to Nistune the ECU, then stop right now and add it to your plan anyway, because the ECU is going to shit the bed over the missing ABS and TC computers that it expects to see, and you need Nistune to stop it chucking all its toys over the side of the crib.
    • kindaruined
      rb20de neo +t conversion - boost pressure sensor needed?

      By kindaruined · Posted

      hey guys, so ive done a complete +t conversion using mostly stock parts on my rb20de neo r34.  Im wanting to know if a boost pressure sensor is needed? Seems like the engine cuts out when i try to do a pull and I have a feeling its because a boost pressure sensor is missing. I'm using a stock r34 rb25det neo ecu.
×
×
  • Create New...