Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Guest RedLineGTR

From my experience the pods that make the most "induction noise" are foam based ones...HKS are the loudest imao Trust airinx (yellow mushroom) are behind it... i have also used (have for sale too) the K&N pod filters your get a noise thats not crazy loud but u still get that induction noise..probably reckon would be one of the quiet ones.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-600954
Share on other sites

I have only used and stuck with the K&N pod. It was the first one i bought and had no need to change it.

On the last "skid pan day" people were asking me "what type of bov. do you have, it sounds made!?" I only have the factory plumbed back system, but you can actually here it work through the pod :cheers:.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601166
Share on other sites

I used to run a Trust Airinix (yellow) pod filter - it was very loud, but IMHO it was very crap at doing what it was supposed to be doing, namely filtering! Took it off to clean it, and holding it up to the light you could clearly see right through it. :cheers:

Call me a pessimist, but if you can see through the filter then the chances are plenty of sh1t can get through and into your engine...:(

I've since ditched it, and replace the stock airbox. OK, it's a lot quieter, but there is no noticeable loss of power and I can rest assured my engine aint breathing in tons of dust and crap on a daily basis..

My 2 yens worth...

But, damn did that Trust pod sound good! :D

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601324
Share on other sites

shuto is right, those blitz metal sus ones are stoooopidly loud. my mate had one on his r33, and it was so loud, you could hear it sucking hard even just cruising without any load at 100km/h in 5th on the freeway.

hks & trust foam filters would be the 2nd loudest.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601551
Share on other sites

just got the K&N pod installed, nice sound not too loud but seems ok.

Was wondering since all you guys have a pod, i want to feed in a cold air pipe down there but couldn't seem to find any holes to feed it. I have a stock Intercooler so that pipe running below the pod is in the way. If you have a cold air pipe, where abouts did you guys feed it?

I left the top bit of the stock box so at least can get some air.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-602185
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...