Jump to content
SAU Community

Recommended Posts

can some one plz describe the effects a sticky blowoff would have

the car jolts 3 times once after you go to about 20% throttle or off boost i spose after you give it over 1/2 boost or so...

i took the bovs out yesterday and one was slightly sticky to push in and would sometimes close momentarily stopping halfway....

is this my drama with jolting? or it is something eles that needs attendance 2?

Link to comment
https://www.sau.com.au/forums/topic/293678-sticky-blowoff-valve-need-help/
Share on other sites

can some one plz describe the effects a sticky blowoff would have

the car jolts 3 times once after you go to about 20% throttle or off boost i spose after you give it over 1/2 boost or so...

i took the bovs out yesterday and one was slightly sticky to push in and would sometimes close momentarily stopping halfway....

is this my drama with jolting? or it is something eles that needs attendance 2?

So does it feel like its missing or actually been forced back?!?

Not something as simple as plugs?

U checked them?

its not a miss as its only when u come off boost. i cleaned all the afm traced back the blow off returns and found that one blow off had a sticky shaft inside... so i put it down to that... the plugs were only changed back a bit but could allways do with a check up.clean i spose.

Hmmm.... Well like ur saying, ur coming off boost (shouldnt be missing then) and its doin the jolting!

I just dont see the BOV jolting the car?!?!

Seems like a fuel/air/spark thing normaly!!!

try completely blocking off the BOV's and see if the car still jolts etc....if not then problem solvered but if problem still there then get some second hand BOV's

but to my little knowledge i dont think its the BOV's causing that issue......

Checked none of the hose clamps have come loose and all intake hoses are on nice and tight?

Had something similar a while a go, when backing off at around 70kmh the car would jolt, was just a loose clamp.

this might be dodgy, but i see no harm, take off the bov or leave it on and spray it with CRC or WD40. to loosen it up.

Good sh!t LOL

Duct tape, zippi ties and WD40 fix anything :(

Any luck so far Adam???

Edited by MYCEF3

All ready tried a clean and lube.. it improved movement a bit but still doing it....

Perhaps someone has a spare set of 33 gtr stock or AM BOV's to lend cheff for half a day to see if that rids the issue?

lol its just such a prick coz basicly the whole front bar needs to come off to get to them lol....

tryed lubing it and it didnt do much. if i blocked it... it will just flutter and hopfuly get rid of the jolt... ill also check plugs... but too all the intake out and sused out all the clamps and hoses and no love...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
×
×
  • Create New...