Jump to content
SAU Community

Recommended Posts

it means as i said earlier... you have either a LEAK or a HEADGASKET problem.

a header tank will not solve this.

if you have done the tests that i and others have mentioned and you are still losing coolant then you have a LEAK or HEADGASKET problem. the heater core which has a flowing path of coolent thro it is one of many possible places for a leak to occur.

stop asking silly questions and start doing some real tests on your car to find the problem.

it means as i said earlier... you have either a LEAK or a HEADGASKET problem.

a header tank will not solve this.

if you have done the tests that i and others have mentioned and you are still losing coolant then you have a LEAK or HEADGASKET problem. the heater core which has a flowing path of coolent thro it is one of many possible places for a leak to occur.

stop asking silly questions and start doing some real tests on your car to find the problem.

I done pressure test no leaking

I changed a cap it doesn't help

the headgasket is fine, because motor is not taking any coolant.

I cleaned the overflow bottle.

I bleeded system

as i said on the topic, it was not losing coolant, the coolant just not fully go back to radiator when cold. I know my question is silly, the problem look very simple, but it just not simple to fix.

Edited by Nosure

did you check the turbo water lines? my s15 in the past (including GTR's) have solid lines i think for water and oil - when under heat, metal expands and moves slightly which can crack the lines

my s15 lost coolant and couldnt figure out why: we pressurised the system and nothing until we put it up onto a hoist and ran the car in-gear = water began leaking out of the turbo water lines.

apparently common; my fix was braided lines to replace the solid ones.

not sure if this is ur problem but though id throw it in anyways, might jst get lucky - all the best mate

-Johnny

did you check the turbo water lines? my s15 in the past (including GTR's) have solid lines i think for water and oil - when under heat, metal expands and moves slightly which can crack the lines

my s15 lost coolant and couldnt figure out why: we pressurised the system and nothing until we put it up onto a hoist and ran the car in-gear = water began leaking out of the turbo water lines.

apparently common; my fix was braided lines to replace the solid ones.

not sure if this is ur problem but though id throw it in anyways, might jst get lucky - all the best mate

-Johnny

thank you, but my turbo is T517Z which is non-water cooled. :(

i have the sae problem as you the car i not loseing coolent what it is doing is when the car gets hot the water expands into the overflow bottle and then when it cools it is only taking about half of it back so when you drive the car a few times it fills the over flow and gets hot cause it not taking the water back

so far i have changed radiator thermostat tryed no themostat changed water pump checked flow through block

the only thing i have left to check is the head gasket i think under load it has a sall leak and is blowing presure into the water side which is overflowing the overflow

Sounds like your head gasket to me??

Is the water mixing in the oil (check oil cap) or oil mixing in the water check rad...

If not any white smoke at all??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy re
    • You don't have an R34 service manual for the body do you? Have found plenty for the engine and drivetrain but nothing else
    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
×
×
  • Create New...