Jump to content
SAU Community

Recommended Posts

Greddy turbo timer - silver

As new condition with nissan adapter.

$60 including post.

Turbosmart boost tee (newer type) in good condition - black

Holds boost well and about 9 months old i might have the box somewhere.

$50 posted.

r33 series 2 floor mats back in excellent condition front okay

$80 posted

Trust/greddy GREX gear knob showing few signs of wear (a touch reddish on parts)

$25 delivered

rb25 polished standard fuel rail and injectors in good condition

$120 delivered

Large type charcoal cannister in good condition

$35 delivered

Blown r33 turbo suit highflow

50 delivered.

Rear Whiteline camber kit.

Brand new. Only used one side of it (all that is usually required)

Good to fix the wearing on the inside of tyres!

$50 delivered (new $140 + post for both!)

Will update with pics soon.

PM me if interested in anything:)

Steve.

Link to comment
https://www.sau.com.au/forums/topic/294800-random-parts/
Share on other sites

Also have a pair of orange standard indicators as per the picture. $35 delivered.

And the Genuine nissan part i'm not quite sure what it is something to do with fuel pressure i believe. It came with the fuel pump kit but i don't need it however. $25 posted.

Cheers:)

Link to comment
https://www.sau.com.au/forums/topic/294800-random-parts/#findComment-4917642
Share on other sites

Turbo timer and camber kit look to be sold already.

Get in quick!

Updated with apexi safc stand $35 posted

Air Flow Meter Adapter to suit rb25 new and unopened - $30 posted!

Link to comment
https://www.sau.com.au/forums/topic/294800-random-parts/#findComment-4917736
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...