Jump to content
SAU Community

Recommended Posts

hey guys up for sale is my 100

asking price 26 grand neg for cash buyer

custom white paint with yellow mica

only kunnys kit in oz bought off kunnys drift car

d max roof spoiler

e boost 2

endless brake pads all round

torsen lsd

yanack extra lock rack ends

yanack tie rods

yanack adjustabl caster rods

custom alloy diff mounts

trd diff bushes

hks coil overs

exceedy ceramic clutch

(dildo gear knob)

custom pwr radiator

greedy cooler kit and solid top rad pipe

am performance split dump sealed sreamer and shortened for louder scream

blits 3 inc zorst

18 inch new deep dish wheels

new water pump timming belt/tenionerand idler

polished engine bay with candy purple bits

polished inlet manifold

j pipe removed and custom inlet made

interior plastics painted candy with marble

in dash dvd screen

prob heaps i forgot but will add

phone nuber 0409454739

post-39491-1257401188_thumb.jpg

post-39491-1257401218_thumb.jpg

post-39491-1257401242_thumb.jpg

post-39491-1257401275_thumb.jpg

post-39491-1257401304_thumb.jpg

post-39491-1257401378_thumb.jpg

post-39491-1257401408_thumb.jpg

post-39491-1257401523_thumb.jpg

Edited by bernardshorty
Link to comment
https://www.sau.com.au/forums/topic/294983-jzx100-chaser-manual/
Share on other sites

  • 2 weeks later...

she realy gotta go i cant get it into my new house driveway and i not lifting it to near stock hight to get it in there hate having it sit on the street atm open to offers

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...