Jump to content
SAU Community

Recommended Posts

brand new australian tein coilovers to suit r32 gtr same as these CLICKY CLICKY brand new never EVER taken out of the box parts easilly available for these and can be easilly repaired rebuilt unlike jap models etc etc$1900

used current model silver hks turbo timer with loom to plug into r32 and 33/s13/s14/s15? $100 with loom in near new condition

used japanese made nismo boost guage with digital exhaust temperature in the middle an awesome guage with the little controller box an older type of guage i know the boost works fine but not sure about the egt as i never ever drove the car to see if it worked correctly but i know it did work as far as i tested it if that makes sense $150

enkei RP01 wheels 17x9 22 offset all round no tyres wheels are 110% straight as i have had these all tested with centre caps a few scratches would be awesome awesome light as fck wheels with some paint currently silver $1100 no tyres

riverside/zepter wheels 3 piece forged polished 17x9.5 17 offset NO GUTTER MARKS NO SCRATCHES PERFECT 4 brand new 255/40 tyres new valvestems all fitted and balanced ready to go all centrecaps and wheelnut cover plates (even have a few spares) $2200 very tough lightweight wheels

genuine cusco alloy gtr r32 hardpipe kit includes fabricated cusco "twin turbo" joiner pipe very very well made a few years old does have some marks but would be great with a clean $280 (remember this includes more parts than your normal hardpipe kit)

noltec r32 front camber arms fitted with brand new nolothane bushes to replace the crappy noltec ones so better than new $220

nardi jap steering wheel the real deal inc horn button slight wear where right hand goes pretty normal $200

used hks pod filters and cast alloy adaptors and brackets to suit gtr $150

HKS evc 3 boost controller worked fine when removed complete with solenoid etc $290

brand new momo race 3000 steering wheel in the box $230

brand new alpine cd/mp3 headunit with usb capability CDA-9884E $290

various r32 gtr parts also available from my parts car im wrecking so if you need anything SEND ME A PM TO ASK

located 1 hr west of brisbane , some prices are slightly negotiable so make a reasonable offer via pm if your interested

will post smaller items no worries if you pay ,but things like wheels and stuff you must organise the freight yourself

post-1868-1257637947_thumb.jpg

post-1868-1257637959_thumb.jpg

post-1868-1257637968_thumb.jpg

post-1868-1257637979_thumb.jpg

post-1868-1257637999_thumb.jpg

post-1868-1257638011_thumb.jpg

post-1868-1257638023_thumb.jpg

post-1868-1257638038_thumb.jpg

post-1868-1257638049_thumb.jpg

noltec r32 front camber arms fitted with brand new nolothane bushes to replace the crappy noltec ones so better than new $220

Is this the adjustable noltec camber? if so I am interested PH:0424 249610

Sam

will organise a pic in the next day or so

will do coilovers and wheels at better rates guys i need them gone!!!

hardpipe kit is sold and gone

Edited by WHITE R32

pics of the nardi

showing the wear also... needs a good clean has original horn button and screws in the tape on the bottom spoke

free postage on this wheel guys!!!

post-1868-1258974016_thumb.jpg

post-1868-1258974021_thumb.jpg

post-1868-1258974030_thumb.jpg

im getting several pm's for items which are sold and masked as sold but ill just do an overall update and price drop in one post...

only the parts listed below are still available for sale and prices have also been lowered again

brand new australian tein coilovers to suit r32 gtr same as these CLICKY CLICKY brand new never EVER taken out of the box parts easilly available for these and can be easilly repaired rebuilt unlike jap models etc etc$1600

used current model silver hks turbo timer with loom to plug into r32 and 33/s13/s14/s15? $100 with loom in near new condition

used japanese made nismo boost guage with digital exhaust temperature in the middle an awesome guage with the little controller box an older type of guage i know the boost works fine but not sure about the egt as i never ever drove the car to see if it worked correctly but i know it did work as far as i tested it if that makes sense $130

enkei RP01 wheels 17x9 22 offset all round no tyres wheels are 110% straight as i have had these all tested with centre caps a few scratches would be awesome awesome light as fck wheels with some paint currently silver $1000 no tyres

riverside/zepter wheels 3 piece forged polished 17x9.5 17 offset NO GUTTER MARKS NO SCRATCHES PERFECT 4 brand new 255/40 tyres new valvestems all fitted and balanced ready to go all centrecaps and wheelnut cover plates (even have a few spares) $2100 very tough lightweight wheels

nardi jap steering wheel the real deal inc horn button slight wear where right hand goes pretty normal $180

used hks pod filters and cast alloy adaptors and brackets to suit gtr $140

HKS evc 3 boost controller worked fine when removed complete with solenoid etc $270

brand new momo race 3000 steering wheel in the box $210

brand new alpine cd/mp3 headunit with usb capability CDA-9884E $270

free postage included in the asking price for most small items

Edited by WHITE R32

they do not have boss kits included but i do have suitable boss kit here for the wheels

pm me and let me know which one you want if interested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...