Jump to content
SAU Community

Can Somone With Datalogit Check My Map Please?

d-ranged

By d-ranged,
in Engines & Forced Induction

 Share

Recommended Posts

pedro skyline Contributor

pedro skyline

Posted
Posted (edited)

I have loads of carbon on the plugs. So it seems to me that i have a lot of fuel added to mixture. Very rich mixture. But it is a bit dangerous to lean the mixture. I will try small increments adjust to the mixture and i will see how rich is the mixture on my wideband. Actualy is showing something like 9.4 on the wideband

Edited by pedro skyline
STATUS Grand Master

STATUS

Posted
Posted

I was wondering is the latency on the injectors left at zero?

And the diferent value set on the injectors is there a reason?

Thanks

To Tune PFC properly the latency is set directly into the table on the left, it is only ever put next to the injectors (via hand controller) to get it to the tuner.

STATUS Grand Master

STATUS

Posted
Posted

Thanks mate for your help. Very much apreciated. This fórum is realy a most with very good People and happy to help. I will logo my datalogit to my pfc and aply those numbers to the fuel injectors sheet on my pfc d-jetro. Thanks i will let you know how was it after that whith the mixture. As long as doesnt knock much and doesnt run lean i will be ok

Post up all your mods or email me [email protected] and i will see if i have a good solid base you can start with. You can buy me a beer next time im in Portugal :P

pedro skyline Contributor

pedro skyline

Posted
Posted

Post up all your mods or email me [email protected] and i will see if i have a good solid base you can start with. You can buy me a beer next time im in Portugal :P

pedro skyline Contributor

pedro skyline

Posted
Posted

Post up all your mods or email me [email protected] and i will see if i have a good solid base you can start with. You can buy me a beer next time im in Portugal :P

By the way i sended to you mail my mods.

I was wondering if i, using a timing light do the 15 degrees advance on the CAS sensor or do i compensate in Apexi PFC ignition avdance sheet? Thanks

STATUS Grand Master

STATUS

Posted
Posted

By the way i sended to you mail my mods.

I was wondering if i, using a timing light do the 15 degrees advance on the CAS sensor or do i compensate in Apexi PFC ignition avdance sheet? Thanks

if pfc hand controller is at 15degrees put timing light on coil 1 (dont use loop at rear unless you are confident of the offset) and set cas so that the timing light and hand controller read the same.

pedro skyline Contributor

pedro skyline

Posted
Posted

Ok mate cheers.

I am doing the injectors at the moment.

I Done 43.5 to all my injectors but the car is running rich on my wideband. I will try to sort my injectors latency cause by my maths is +0.24ms

But the car is steel running rich so probably it is a diferent latency. Cheers

  • 2 weeks later...
pedro skyline Contributor

pedro skyline

Posted
Posted
On 28/06/2016 at 10:07 AM, STATUS said:

Just let me know if you received my email with my mods thanks

 

yeah im back friday so i will forward something through

Hi again status. I tryed the map you sended me and made some adjustments and car runs fine thanks alot. Now my exhaust manifold is cracked lol. I am looking for one more resistant then this one. And i have a problem with my ecu 2 pin temperature sensor. Car takes time to start and when start i warm up for a while and when a turn engine of for 10m the reading in the ecu is like -22 degrees wich is impossible.

I bought a new one and it does the same thing any ideas?

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...