Jump to content
SAU Community

Recommended Posts

OK, Just had the ole' RB26 rebuilt and now these parts have to go. Postage is available on some items and the rest are pick up only from Homebush in Sydney.

Item 1: Stock R33 GTR turbos. They have done 94000kms. When the GTR came over from japan it was compression tested and the results were 272 in all cylinders! No shaft play at all. These turbos have never seen a hard day in thier life. - $500ono. Pickup only.

post-16592-1257683538_thumb.jpg

post-16592-1257683573_thumb.jpg

post-16592-1257683608_thumb.jpg

post-16592-1257683637_thumb.jpg

Item 2: Greddy Profec E-01 Boost controller. High/low and overtake boost control modes with manual control or full auto. Boost data logging capability up to 3 hours. Great condition. - $400. Can post at buyer's expense.

post-16592-1257684428_thumb.jpg

post-16592-1257684456_thumb.jpg

post-16592-1257684478_thumb.jpg

Item 3: Stock RB26 cam shafts, PC - $200. Pickup only.

Item 4: Stock RB26 injectors, PC - $300 the lot with rings. Can post at buyer's expense.

Item 5: Near new Nissan R33 GTR clutch fitted by Prince Oita in Japan just before shipping. Did about 4000kms in Australia before being replaced with a OS Giken STR Twin Plate. Great OEM replacement item. - $150. Pickup only.

Send a PM if more info is needed.

Link to comment
https://www.sau.com.au/forums/topic/295434-rb26-parts-for-sale/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...