Jump to content
SAU Community

Recommended Posts

Good day!

Does anyone know the exact location of the fuse box for the v35 model ? my skyline has got the air bag light on. I just want to try removing the fuse & clean it a little bit.

cheers

"Turn the key to the on position and watch the airbag light. It should stay solid for 5-7 secs, and then turn off, and then start to flash.

To reset the light, you must turn the key to on, watch the airbag light stay solid for 5-7 secs and as soon as the airbag light turns off, turn the key to the off position (you have to turn the key to off before the airbag light starts to flash, or you must start over). You need to repeat this 5 times. Try to start the car, and hopefully the light will be reset"

No more Air Bag flashing light or Nav screen warning!!

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4925485
Share on other sites

"Turn the key to the on position and watch the airbag light. It should stay solid for 5-7 secs, and then turn off, and then start to flash.

To reset the light, you must turn the key to on, watch the airbag light stay solid for 5-7 secs and as soon as the airbag light turns off, turn the key to the off position (you have to turn the key to off before the airbag light starts to flash, or you must start over). You need to repeat this 5 times. Try to start the car, and hopefully the light will be reset"

No more Air Bag flashing light or Nav screen warning!!

cheers, i will try this

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4925498
Share on other sites

I took it & they pluged it in to the computer the out up was " B1166 LH (Open)

Meaning, the fault is LH curtin air bags. & my car doesn't have side air bags.

& the light is back on.

Any interstate professinals have you had this experince before ?

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4938929
Share on other sites

I have the sedan.

I'll give you something else to check, cause I'm having the same issue as well. The scanner gave me some wierd message like yours too(can't remember if it was the same though as it was ages ago).

Under each of the front seatbelts there is a connector with a wiring harness. Is it loose? Check both front seatbelts. I snapped the connector one day while trying to adjust it(bloody things don't move). And since then the airbag light comes on. If I hook in the connector with a cable tie, it's good. If I play with it, airbag light comes back. Finally decided to order the part from Japan, will be here in a few weeks.

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4941063
Share on other sites

Thankx Skizo, that sounds more like it. did u have it coming each time you were driving ? what was ur error code? B1166 ?

Because the scanner said LH side I gave the LH seat & wiring a good shake & reset using the ON/OFF x 5times. & I have driven about 100k's all around & it still hasn't poped up. so hopefuly it's gone for good.

there is soo much wiring under that seat.

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4941547
Share on other sites

Can't remember the code, it's been so long since i hooked up a scanner to it.

Yes the airbag light would come on every time I drove the car. Even after a reset, it would be back the next time I drove the car, until I cable tied it. So in my case I believe that the broken seatbelt connector on the buckle was the issue.

If it comes back let me know as there are some more detailed things you can check as well.

Link to comment
https://www.sau.com.au/forums/topic/295446-v35/#findComment-4942692
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...