Jump to content
SAU Community

Recommended Posts

Up for sale is a Nissan Skyline R34GT-T in Silver Color, Manual transmission, Factory Xenon HID headlight. Traction control & ABS

Imported since last year September with 70000kms and i am the first owner in Australia.

The car is in very good condition and well look after. Service every 5000kms with full synthetic engine oil.

Always fill with 98 Octane Petrol like BP ultimate or Shell V-power

Very long Registration until September 2010

Car has the following modification carry out from Japan:

Fujitsubo Turbo back exhaust including dump & front pipe

Ohlins Coilover suspension with height & damper adjustable

18" BBS rims, front: 18x8.5J +36 Rear: 18x9.5j +38

Short shifter

Apexi air Filter

The car has the following things replaced at last year Sept

Brand new heavy duty battery

Changed transmission oil with brand new Reline gear box oil

Changed Diff oil

Changed engine oil

Brand new EBC green stuff brake pad on the front

Brand new bendix brake pad on the rear

Brand new Greddy full auto turbo timer

Brand new 2way alarm system

Approximately 6 months ago, I replaced the coilpack with a set of Brand new Spiltfire Coilpack due to the original one was misfiring. (common problem on Nissan vehicle)

Recently replaced the tyre with a set of brand new Kumho KU36 $1000

Front: 235/40/18

Rear: 275/35/18

Have the window tinted 2 months ago.

Genuine Nissan Aero front bumper bar (plastic)

Genuine Nissan Aero side skirt (plastic)

Matching Rear pod (fiberglass)

Came with Factory Skyline carpet , Factory Skyline Manual & some Japan service history

A very reliable car in very good condition, come with RWC, genuine reason for sell, Price Negotiable

$19999 with RWC, contact Benny on 0433887191 or email [email protected], I may not able to pick up your call during work, drop me a sms if you cant reach me.

Car is in VIC, SE melbourne

SNC00195.jpg

SNC00200.jpg

SNC00189.jpg

SNC00192.jpg

SNC00193.jpg

SNC00198.jpg

SNC00197.jpg

SNC00192.jpg

Edited by benny_melb
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...