Jump to content
SAU Community

Recommended Posts

1997 R33 Series 2 120,000kms

I have owned the car for a little over a year, before that it was owned by a friend for a about a year.

Serviced Every 5000km or less with Motul turbo light 10w 40w

Motul Diff Oil

Redline Gearbox Oil

Modifications,

Apexi Power FC Tuned at 12psi (made 201kw)

Blitz Dual SBC boost controller

Split Fire Coil Packs

Walboro Fuel pump

Blitz turbo timer

R34 Turbo (OP6)

RB20 Wastegate Actuator (10 psi)

Split Dump/front Pipe

3in Hi Flow cat (inside not bashed out)

3.5 inch HKS Hi Power Exhaust

Apexi Power intake filter on custom made Metal intake pipe onto the turbo

(Pod not totally boxed in but covered over see photos below)

Standard RRB20 Blow off valve

Greddy Front Mount Inter cooler and piping

Alloy Radiator

Heavy Duty Excedy Clutch

Braided Clutch Line

Braided Brake Lines (ADR approved)

Master cylinder stopper

Front and Rear Strut Braces

Bilstein Shocks and King Springs

Front Whiteline adjustable Castor Bushes (adjustable on car)

Rear Whiteline Camber Bushes

Work Emotions CR KAI 18 x 8.5 in all round

235/35/18 federal 595 SS on the front (70%)

235/35/18 Sumitomo HTR Z 3 on the rear (70%)

Work Wheel Nuts

M Spec side skirts and rear pods

33 GTR rear seat

Have had the Roof lining, A-Pillar and B/C Pillar trims redone in Black Suede (haven't done the sun visors yet)

Only need front GTR seats and interior done

White LEDs' in the cluster

Have Changed the AC Panel, cigarette lighter surround and ignition barrel surround lights all to blue LEDs'

Pioneer Head Deck (DEH-P6850MP)

Pioneer Front Speakers and tweeter

Pioneer Rear 6in Speakers

And finally the rear "Skyline" Boot garnish lights up red with taillights

There is probably more little bits and pieces i have forgotten but i think that will do, Basically the car has never missed a beat in the last 2 years runs great drives beautifully and handles well. Overall i think its one of the nicest R33's running around. Has been my pride and joy for a little over a year but its time for me to move on, Pictures Below feel free to ask any questions.

Price - $18,500 Will get RWC upon Sale

Plates Not Included

PM for my contact details if you are interested

and have a few more photos too

Cheers Scott

post-29410-1258113283_thumb.jpg

post-29410-1258113298_thumb.jpg

post-29410-1258113313_thumb.jpg

post-29410-1258113346_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/296181-1997-r33-series-2/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 5 weeks later...


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...