Jump to content
SAU Community

Recommended Posts

SELLING A MANUAL GEARBOX R32 GTR BEEN RECENTLY PULLED OFF. SORRY I DONT HV ANY PICTURES OF IT BUT IT COMES TOGETHER WITH THE GEAR STICK WITHOUT THE KNOB. SELLING ONLY THE GEARBOX IF U WANT THE CLUTHCH PLATE ITS SEPARATE. ITS AN UPGRADED CLUTCH PLATE NOT SURE OF WHAT BRAND. BUT WILLING TO LET IT GO FOR $500. THE PRICE FOR THE GEARBOX WOULD BE $2000 FIRM. CALL ME IF U HV ANY INQUIRIES. WILL NOT POST ONLY PICK UP. CAR HAS DONE ABOUT 130000 KMS REZA 0432415424.

HAVE HEAPS OTHER PARTS AS WELL, INCLUDING DRIVE SHAFTS, CROSS MEMBER, STARTER MOTOR, FUEL PUMP, FUEL TANK, STOCK SPOILER, BOOT, LEFT FENDER, BOTH DOORS, WINDOW MOTORS, AFTER MARTKET EXHAUST NOT SURE WHAT BRAND, BRAKES COMPONENTS, CLUTCH MASTER CYLINDER, BRAKE MASTER CYLINDER, BUCKET SEATS MINT CONDITION, STEERING WRECK WITHOUT RACK ENDS, 19 INCH RIMS WITH TYRES HAS A STRATCHES FROM THE ACCIDENT, TAIL SHAFT, DIFF, TIEN REAR SHOCKERS WITH SPRINGS.

IF U WANT FAST RESPONSE I WOULD ADVISE YOU TO CALL ME AS I DONT OFTEN GET THE CHANCE TO GO ONLINE.

FOR ALL THE ITEMS ABOVE, JUST MAKE AN OFFER. ANY OFFERS MIGHT BE CONSIDERED. JUST WANNA GET RID OF THESE ITEMS. BUT PLEASE MAKE REALISTIC OFFERS

post-36577-1258607669_thumb.jpg

post-36577-1258607724_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/296914-heap-of-r32-gtr-parts-for-sale-melb/
Share on other sites

Price on front drive shaft??? or just the rhs inner cv joint???...delivered sydney......

front drive shafts 120 each...delivering im really not sure how do i go about doing that..if u can suggest anything im willing to send the pair at buyers cost

Hey mate i'm 3 sensors.

The first one is the out side temp sensor ( located near the aircon fan )

The second is inside temp sensor located in the center console near the cig lighter.

The third is the sunload sensor which is located in the dash passenger side top near the windscreen.

How much for these sensors.

Oh and can you confirm if your aircon was working

ahha nothing..i just dont know what they go for...i assumed it was much more as the r33 gtst was around 1k

r33 gtst ones can handle more power. harder to come by as more everyone wants them... going rate for r32 gtr is around 5-600$

  • 2 weeks later...

Hey mate

im after the rubber spacer that goes under the gtr wing on the outside drivers side.

Not the one that gets bolted down but the outside one.

Can pick up.

If you have it how much do you want?

Need it bad

Cheers mate

  • 7 months later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...