Jump to content
SAU Community

Recommended Posts

1994 Nissan Skyline R32 GTR. Last of the R32 GTRs to come out.

Purchased October 2007, handpicked and imported from Japan (First owner in Australia).

Immaculate condition, no rips, tears or fading on the seats or steering wheel. No broken vents on dashboard.

Still has the original paintwork.

62,000kms.

Burgundy.

Rego until October 2010.

Done 10,000kms since purchased in 2007.

Car does not come with personalised number plate.

Major service carried out at 58,000 kms replacing all oils including gearbox, diff, transfer case, brake fluid and engine oil.

Dynoed on Dyno Dynamics with 280.6kWs at the rear wheels.

Modifications:

Spent more than $15K for all the mods which were bought brand new (most of the mods have only been in the car for approximately 3000kms)

  • Alarm with SMS paging
  • Tracking device fitted – needs subscription and monthly payments
  • Tein super street suspension
  • Apexi pod filters
  • Alpine head unit (USB hard drive compatible)
  • Clarion splits at the front
  • Kenwood Amp running a clarion sub
  • Power FC with hand controller
  • Blitz boost controller (Dual Solenoid)
  • Cusco strut braces front and rear
  • Nismo super copper mix twin plate clutch
  • Grex oil cooler with relocator
  • Ferrodo DS2500 brake pads (front)
  • Work XD9 18x10 wheels with Nankang 265/35/18 rubber (No gutter rash)
  • Garrett 2860R-7 turbos (stock turbos available – from the condition of the stock turbos the car was not thrashed).
  • Sard 700cc injectors
  • Greddy cam gears
  • Greddy belts
  • Greddy clear cam cover
  • Nismo fuel pump
  • Nissan water pump and bearings
  • Spark plugs replaced recently
  • 4WD switch installed (so you can run on rear wheel drive mode)

Work carried out in a reputable workshop in Melbourne.

Receipts and most of the original parts available on request.

$25900 ono comes with RWC

Genuine reason for sale

Contact Las on 0422975657

post-41829-1259488829_thumb.jpg

post-41829-1259488904_thumb.jpg

post-41829-1259488929_thumb.jpg

post-41829-1259488985_thumb.jpg

post-41829-1259489000_thumb.jpg

post-41829-1259489017_thumb.jpg

post-41829-1259489042_thumb.jpg

post-41829-1259489074_thumb.jpg

post-41829-1259489096_thumb.jpg

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

if this is the one ive seen on bergins rd or @ knox city, then this is in immaculate condition, really nice gtr

Thanks mate

You've probably seen the car at Knox a few times

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...