Jump to content
SAU Community

Recommended Posts

Hi All,

Just wondering who has installed Dayz skirts onto their S1 stags that didnt come with any skirts? How did you do it? Could someone with a S1 Dayz tune car (finger pointing at Brendan) take some photos of under the skirt ect and that will show how they come factory mounted to the car ( at front back and along it.... ect ect)

Not to phased either way if I end up putting them on or not, but If I do i dont want them being tacky.

Cheers all,

Chris

Link to comment
https://www.sau.com.au/forums/topic/299923-side-skirt-instillation/
Share on other sites

Its screwed on with 2 screws in both wheel arch areas

Id suggest that along the length there would be epoxy glue holding it onto the body

do you want to catch up and have a look with ya own eye?

Tangy- Theirs deff 1 screw in front guard, two in rear and some along the length of the skirt then some clips to..... But got no idea where it all ataches apart from the arch bolts

Will be in touch rodders, still not super sure if i want to put them on or not.

I've got a nismo Kit on mine. It has press in clips down the side and brackets underneath. There is one or two screws inside the frond guard and a separate cap at the other end which clamps to the inner guard lip and has tabs which interlock with the side skirt.

For anyone that was interested or watching this;

Rod and Aleks came over this arvo to help me put them on. After a bit of looking about we decided to give it a crack when we have more time on our hands as the skirts use a different mounting set-up to both of their rs4 skirts. Also sceptical if they are stock dayz skirts or not, the donor car is a dayz and appears to be un touched but as we know anything is possible in the motherland...

Will give an update next week some time once we've had another go.

Thanks to Rodney and Aleks to coming around :3some:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...