Jump to content
SAU Community

Wtb - Stub Axle + Rhsr Cv Shaft - R33 Gtr V-spec

d_liberate

By d_liberate,
in Wanted to Buy

 Share

Recommended Posts

Deano45 Rising Star

Deano45

Posted
Posted
Im chasing the following parts for a mates 96 R33 GTR V Spec

- Aluminium Housing or Stub Axle that the bearing hub bolts into.

- Right hand Rear drive shaft or CV shaft.

:3some:

What's wrong with the current ones?

Where are you located? as it will help readers know where you are to suggest somewhere

Are you after new or second hand ones?

I take it the stub axle is for the same side on the rear?

Have you tried a wrecker or a CV reco place?

d_liberate Collaborator

d_liberate

Posted
  • Author
Posted
What's wrong with the current ones?

Where are you located? as it will help readers know where you are to suggest somewhere

Are you after new or second hand ones?

I take it the stub axle is for the same side on the rear?

Have you tried a wrecker or a CV reco place?

The car kissed a curb on the right side rear and most of the other issues have been fixed but it has also stuffed the bearing, stub axle and the cv shaft.

Tried a couple of wreckers but they only have R32 GTR bits in stock and they charge an arm and a leg.

Located on the south coast of NSW so would probably have to get couriered.

:3some:

Deano45 Rising Star

Deano45

Posted
Posted
The car kissed a curb on the right side rear and most of the other issues have been fixed but it has also stuffed the bearing, stub axle and the cv shaft.

Tried a couple of wreckers but they only have R32 GTR bits in stock and they charge an arm and a leg.

Located on the south coast of NSW so would probably have to get couriered.

:cheers:

Don't know exactly where to go down there but you can try SSS Automotive

Alternatively take your shaft to a CV reco place and see if they can rebuild it

For parts like the bearing have a look on the forums or take it to a bearing place to see if they have something the same. If all else fails go to nissan spare parts.

Anything on a GTR is expensive.

Good Luck

d_liberate Collaborator

d_liberate

Posted
  • Author
Posted
Don't know exactly where to go down there but you can try SSS Automotive

Alternatively take your shaft to a CV reco place and see if they can rebuild it

For parts like the bearing have a look on the forums or take it to a bearing place to see if they have something the same. If all else fails go to nissan spare parts.

Anything on a GTR is expensive.

Good Luck

Thanks for the info. Ive already picked up a bearing and hub. The problem is from the hit, and I think the mechanic cant seperate the CV shaft without doing more damage......

I'll give SSS a call tommorow and see what they can do. :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
×
×
  • Create New...