Jump to content
SAU Community

Recommended Posts

If you've been playing around with double-clutching, along with all the before-mentioned symptoms I'd say your clutch is on the way out. You may have been burning it quite well while you were learning to double.

@David

Car revs as normal, I was very sure whe boost was taking longer to spool, but that may have been my imagination. When the car was running, it took ages to build speed. But as I said in my last post, car is no longer working. Just sits there in first revving its heart out.

@Mosquito

Given the fact I've never had any issues with the clutch before now. I'd say I probably did stuff it while learning to double.

If the clutch is gone, should I go ahead and get my syncros replaced while the box is out?

Can anyone give me a ball park figure on getting my syncros replaced?

Cheers

Edited by Aidan

Id also say forget about the synchros, just get a new clutch. Exedy OEM replacement + labour goes aroun 600-800 total, roughly...

Or go for an Exedy Heavy Duty + labour maybe around 800-1000?

  • 2 weeks later...

If the turbo suddenly takes longer to spool up the issue could be a blocked/collapsed catalytic converter.

I had a hi flow metal cat that I bought through an SAU group buy a few years ago, that the insides collapsed and blocked up a few months ago.

The only symptoms were a slower spool up of the turbo, and my peak boost decreasing below what the EBC is supposed to maintain.

I thought the Boost controller was the issue, so I swapped that out, with the same results. So next I thought the wastegate could be the issue, and swapped that also. After this didn't fix the problem, I took off the cat and had a look. It was almost completely blocked due to the breakup of the stainless mesh inside.

It was a frustrating learning experience, as the cat would have been a pretty simple thing to initially check. I guess I figured when you spend good money on a stainless "Magic Cat" it should last more than 18 months.

Sorry to hear about your gearbox breakage, but while your fixing that issue, I'd also take the cat off and have a look inside.

Ahh double clutching should be more beneficial for your synchros but only if you do it right! If you rev too high and engage the clutch it will jump forward and put more strain on the drivetrain and too low will make pull it back similar to normal downshifting. The whole idea is to keep it smooth and get the revs matching right before engaging the gear. It should be seamless between downshifts.

Edited by Ruff Ryda

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...