Jump to content
SAU Community

T04e Oil Restrictor Size?

RicsR33

By RicsR33,
in Engines & Forced Induction

 Share

Recommended Posts

RicsR33 Enthusiast

RicsR33

Posted
Posted

Hi guys

I just put the engine back in my R33 with a T04e (brand new) (bought it off someone who didnt want it anymore but looks like it is probably a cheapy), now i have cranked up the engine, it all runs fine but i give it a few revs (4000rpm) starts blowing smoke while reving and then at idle after that until it settles down again. Im pretty sure my turbo requires a restrictor, now i have left the stock bolt in the block which has a restrictor in it i believe, but i believe i also need one on the turbo side as well? am i correct? now with the line im running at the momment looks like it has a 2mm-2.5mm fitting (turbo side) is this too big? or is my problem not turbo oil related? cheers

Link to comment
https://www.sau.com.au/forums/topic/301545-t04e-oil-restrictor-size/
Share on other sites
RicsR33 Enthusiast

RicsR33

Posted
  • Author
Posted

the drain isnt kinked or blocked, but once i placed the restrictor in today the smoke has settled heaps, should i take it back out and see if it smokes again? i have read from other forums that i should use a restrictor as the pressure pushes past the seals on a T04e but sounds to me they could be wrong, i did not use silicon on the drain only a gasket. What is everyones suggestions? rip the restrictor back out?

hypergear Grand Master

hypergear

Posted
Posted

Should never restrict oil to a sleeve bearing T04E turbo. specially if its oil cooled. Without oil pressure and flow the bearings worns out in a lot faster rate. Smoking with no shaft play means the bearing housing is flooded with oil. Find out why it can't drain oil is the key to fix this problem. Unless the CHRA of the turbo is very poorly built.

RicsR33 Enthusiast

RicsR33

Posted
  • Author
Posted

using the stock drain pipe although the hose is a little monged (not fully kinked), could be flowing alot better, is the stock drain suffient? im guessing it would be the drain, just cant seem to find a good hose that will fit perfectly.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

your factory turbo drain?

no good, factory turbo flows less oil - you need a larger line, this will be causing pressure blowing oil past the seals.

My oil drain for my T04E i could easily stick my index finger in down to my first knuckle so it was what... 2.5cm diameter or so?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...