Jump to content
SAU Community

Recommended Posts

yeah its wierd that when the engine is running it doesnt go anywhere near the normal values

that would make the car run like ass as the ECU has mapping and fuel enrichment etc based on TPS (and AFM, but TPS is also used)

so whilst your floor it, the ECU doesn't detect you are flooring it and thinks the engine is only under some minor levels of load even though AFM is probably showing normal full voltage

I had to take it out for a 10 min drive just then and something occured to me -- the aftermarket cruise control is not turning on now (was working 2 days ago). Do they connect in with the TPS? I will have a look tomorrow.

I had to take it out for a 10 min drive just then and something occured to me -- the aftermarket cruise control is not turning on now (was working 2 days ago). Do they connect in with the TPS? I will have a look tomorrow.

What TPS will fit? It has 6 wires coming out of it, going into 2x 3-pin connectors. After some research, I need another auto one.. What about an auto rb30e?

Edited by revolt
What TPS will fit? It has 6 wires coming out of it, going into 2x 3-pin connectors. After some research, I need another auto one.. What about an auto rb30e?

Sigh, the saga continues. The TPS, when on WOT does momentarily register over 3v. However, the other figures are accurate >> 6k RPM was 1.2v..... 3k RPM was about 0.7v. Idle is 0.4v.

6k rpm at idle only requires slight throttle, so that is why it's only showing 1.2v. I think this is working properly. Also, if the 0.40v at idle is correct, it should idle properly if the TPS was the problem shouldn't it?

I am gonna look up what readings the CTS is supposed to give and test that.. because when I was testing just then, the car was up to temperature, but revved did not drop. Stayed at 1500rpm. argh.

EDIT: CTS is definitely working when hot.. measuring 300 OHMs, exactly what it is supposed to be. ;)

ARGH, Pages 47-52 on the R34 workshop manual here-- http://www.importworkshop.com/nissanskyline.html -- all of my sensors are registering perfectly. Time to grab a boost gauge I guess and see if vacuum is weird. Wouldn't a vacuum leak cause idle problems straight away though? Not just when warm?

Edited by revolt

Hey mate, I just went through a very similar problem to urs. Thought of everything and did everything and couldn't find out where the problem is coming from. Chucked in on the dyno, everything was fine, took it to a performance shop and got computer diagnosis and it returned as normal, anyway, found out it was the air filter box, worn. Changed that and only $300 later and my car runs like a dream. Perhaps ur experiencing the same problem. Check the condition of ur box and look for loose wires etc.. So anyway, Mine was doing it at 2600rpm.. Sounds v similar to ur prob though.. Hope it helps

Do you mean the Air Flow Meter in the airbox?

Cleaned that and checked the voltages. All perfect according to the workshop manual. :blink:

Put some Injector cleaner + 98 octane through it today and took it for a 20 min drive. It now stutters badly from 2-4k ish rpm, then all of a sudden comes good from 4 til it changes.

Hopefully borrowing a Consult cable from Chuckie (and maybe try another AFM/TPS), so hopefully that sorts it out.

Hey mate, I just went through a very similar problem to urs. Thought of everything and did everything and couldn't find out where the problem is coming from. Chucked in on the dyno, everything was fine, took it to a performance shop and got computer diagnosis and it returned as normal, anyway, found out it was the air filter box, worn. Changed that and only $300 later and my car runs like a dream. Perhaps ur experiencing the same problem. Check the condition of ur box and look for loose wires etc.. So anyway, Mine was doing it at 2600rpm.. Sounds v similar to ur prob though.. Hope it helps

Problem possibly solved. :D

Today I pulled off all of the intake hoses.. couldn't see any cracks or brittle sections. Replaced 2 small vacuum hoses that were starting to get old, but I doubt they were leaking, I untaped the coil pack harness and looked at the wiring.. looked all good.

I then put my OLD COIL PACKS in (which were causing the ECU to give a coil error, but worked fine).... car is idling perfect after 20 mins running. I will drive it around today with the oil packs in, then swap the almost brand new coil packs in and see if the problem comes back.

:) Won't be happy with the $500 coil packs already have problems after ~5000km.

Yeah.. Super Sparks.. Yellow Jackets weren't available for the NEO when I was looking. :rofl:

Super Sparks right? Havnt heard great things about them.

Yellow Jackets seem to be the go for the non-Japanese coil packs.

  • 4 months later...
A few weeks ago my S2 Stag developed a very slight misfire at idle. Previous to this, it has always been super smooth (have to look at tacho to see it's running).

Sounds like I may have a similar issue with my R34 GTT, more details here.

I am getting code 34 though (knock sensor) so will need to look into that first. If that doesn't help I'll follow your list to see if anything there would resolve it.

Did you get this sorted completely since the January update?

  • 1 year later...

Problem possibly solved. :D

Today I pulled off all of the intake hoses.. couldn't see any cracks or brittle sections. Replaced 2 small vacuum hoses that were starting to get old, but I doubt they were leaking, I untaped the coil pack harness and looked at the wiring.. looked all good.

I then put my OLD COIL PACKS in (which were causing the ECU to give a coil error, but worked fine).... car is idling perfect after 20 mins running. I will drive it around today with the oil packs in, then swap the almost brand new coil packs in and see if the problem comes back.

:) Won't be happy with the $500 coil packs already have problems after ~5000km.

mine lasted a bit longer... bought about 25mths ago, probably installed about 50ks ago. All of a sudden after a boot full on a cold morning at least one of them gave up.

Super Sparks right? Havnt heard great things about them.

Yellow Jackets seem to be the go for the non-Japanese coil packs.

thought they were ok!

Yeah.. Super Sparks.. Yellow Jackets weren't available for the NEO when I was looking. :rofl:

put my stock ones back in, that'll do for the moment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It’ll be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
    • Light should be a pressure switch, not a sensor.
×
×
  • Create New...