Jump to content
SAU Community

Leaking

stormtrooper

By stormtrooper,
in Western Australia

 Share

Recommended Posts

stormtrooper Proficient

stormtrooper

Posted
Posted

Hey guys,

Was out for a drive last night on a cruise, taking it easy. At one of the meet points, Ken34 and my cousine noticed that I had fluids leaking from the front of my car. At further inspection this proved itself to be coolant.

I drove it home cautiously, monitoring the water temp on the power FC controller, and didn't go above 85c at all. This morning I come out to have a look and see whats what, notice that the radiator is about half empty and so I start looking around.

I filled the radiator up with water (just to test, going to flush again later) and turned the motor over. Didn't take more than about 10 seconds and already the leak was apparent. Looks like it's coming from the water pump on the block. Now I'm not sure if it's one of the bolts (can't see) or if it's coming from the seal and leaking through the hole (which means it's stuffed, obviously). Not sure what to do here as I had her at Xspeed a few weeks ago and they did a full timing belt service on it for me, replacing the water pump at the same time. Is there any way I can stop the leaking for the time being or will I have to take it back to them sometime to get this resolved? Also, what are my rights in this situation being that the water pump is brand new?

-Chris

Link to comment
https://www.sau.com.au/forums/topic/302277-leaking/
Share on other sites
Nic_A31 Grand Master

Nic_A31

Posted
Posted

How far from XSpeed are you?

Tighten the bolts as much as you can, and drive it with a few 1litre bottles of water with you and stop at service stations if you need to.

I dropped 80% of my water in Ozzy Park at the freeway on ramp, topped up, limped it home to Swan View and fixed it, wasn't too hard, just avoid stop/start traffic and main roads, if you do have to stop, you want to do it in a back road.

Link to comment
https://www.sau.com.au/forums/topic/302277-leaking/#findComment-5014026
Share on other sites
stormtrooper Proficient

stormtrooper

Posted
  • Author
Posted

Cheers Nic. I live in Palmyra, literally 5 mins up the road from Xspeed, so I don't think that overheating on the way there is going to be an issue hehe. Last night, I managed to drive from the meet point we were at, car park off selby st Osborne Park, back to my cousines place in Belmont. Then from there to my house in Palmyra, all without the water temp going over 85c. However this morning the water had drained to about half capacity in the radiator itself. I'll be able to get it there ok.

Link to comment
https://www.sau.com.au/forums/topic/302277-leaking/#findComment-5014122
Share on other sites
stormtrooper Proficient

stormtrooper

Posted
  • Author
Posted

Nah the guys at Xspeed are a good bunch. Hansons a great guy to talk to, knows his stuff.

Fairly sure it would be the gasket/seal between the water pump and the block itself. I'd rather just have the fellas do it however so as not to void any warranty or anything by doing it myself hehe. I was going to throw some fiberglass sealant stuff through the system today and hope it sealed the leak but decided against it as not sure how it'd affect warranty or anything.

Link to comment
https://www.sau.com.au/forums/topic/302277-leaking/#findComment-5014735
Share on other sites
KEN-R34 Community Regular

KEN-R34

Posted
Posted
yes, kenr34 is an awesome guy

Haha.. This is the guy who noticed it was coolant ;) Mr. oz, I just gave him a rag to wipe his filthy hands before he got into my car!

We all thought it was oil at first haha I think your heart skipped a few beats.

Good to hear everything worked out ok. Was good meeting you on the cruise mate, we should cruise again once everything is sorted.

Peace,

Ken

Link to comment
https://www.sau.com.au/forums/topic/302277-leaking/#findComment-5015198
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      first time swapping rb25det into r34

      By Murray_Calavera · Posted

      This sounds like a perfect excuse to install a Haltech R3.
    • Kinkstaah
      first time swapping rb25det into r34

      By Kinkstaah · Posted

      I do believe from context he is talking about a S0/S1 R33 RB25 with associated ECU and Wiring for that, and a manual gearbox into a R34 N/A Auto. I don't have the knowledge of all the pinouts and such but my gut feeling from doing my own conversion is to use as much of the R33 stuff that you can. The "car" wiring is quite seperate from the "Engine" wiring when all things are considered. The only things to truly consider 99% of the time is the cluster, reverse lights and potentially disabling the 'not in P/N' immobilizer circuit.
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      A realistic expectattion of how long it has to last also comes down to.... when do you think you will be banned from registering and driving old petrol powered shitters? It's 27 years since that thing was built. It probably rusted out 15 years ago. It was probably repaired and looked OK for another 10. If you do a similarish bodge job now, or perhaps slightly better with some actual rust conversion and glassing, then.... get another 10-15 years out of it, after which you'll only be permitted by the CCP to drive electric cars manufactured in their Shenzen zone anyway. 
    • GTSBoy
      first time swapping rb25det into r34

      By GTSBoy · Posted

      Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • WR33KD
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By WR33KD · Posted

      I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
×
×
  • Create New...