Jump to content
SAU Community

R33 Gts25t Wont Start...

Jarsky

By Jarsky,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

Jarsky Apprentice

Jarsky

Posted
Posted

Hey Guys,

I've never had a problem with my latest skyline....until today :/

I drove it to work this morning just fine, try to go out and get some lunch and now it just wont start.

The starter is going nice and strong so it definately isn't an issue there or with the battery - but I can't hear it trying to turn at all.

I've checked the fuel pump fuse which is good and checked the lines aren't leaking or anything - all the fuel lines look good. Is it most likely going to be the fuel pump has died? Could it be an electrical problem as well?

any help appreciated - currently stuck at work :D

Link to comment
https://www.sau.com.au/forums/topic/303334-r33-gts25t-wont-start/
Share on other sites
Craig SLO33 Enthusiast

Craig SLO33

Posted
Posted
so its turning over but not firing up is that right ?

check fuel supply easily by undoing the inlet hose to the fuel rail and turning the motor over, fuel should come out the hose...i would disconnect the coils so it wont fire up on u when u turn it ova..

Jarsky Apprentice

Jarsky

Posted
  • Author
Posted

thanks Craig - will try that when I get the car home (decided to get it towed home from work), someone else also suggested I try that to check the fuel pump is working.

and yeah - the engine is 'shaking' when I turn the key and starter is spinning quite hard (starter is only about 4 months old) making a 'RARARARARARA!!!' noise, so from what I can tell the starter motor is cranking the engine - but seems to be either a lack of fuel or a lack of spark. im leaning towards fuel as I can't hear the fuel pump priming - so i think that will be my first place to check

Craig SLO33 Enthusiast

Craig SLO33

Posted
Posted
thanks Craig - will try that when I get the car home (decided to get it towed home from work), someone else also suggested I try that to check the fuel pump is working.

and yeah - the engine is 'shaking' when I turn the key and starter is spinning quite hard (starter is only about 4 months old) making a 'RARARARARARA!!!' noise, so from what I can tell the starter motor is cranking the engine - but seems to be either a lack of fuel or a lack of spark. im leaning towards fuel as I can't hear the fuel pump priming - so i think that will be my first place to check

No probs let us know what happens, gd luck

Jarsky Apprentice

Jarsky

Posted
  • Author
Posted

only just got the car home last night (towed it home myself after 2 tow trucks did a no show)

decided to put it in diagnostic mode, unfortunately returned code 55 telling me everything is fine :)

next step....check the fuel pump & spark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...