Jump to content
SAU Community

Recommended Posts

a good upgrade might be a factory GTR clutch and flywheel (from early R32) i have a billet lightweight GTR flywheel and Excedy HD GTR clutch in mine, clutch grip is phenomenal (second gear clutch drop lights all 4s with fat tyres) on RB25DE+T but you pay for it with your left leg, it is brutal heavy and bitey, Ive got a mate with a 4000lB Jim berry full monty clutch, and that's light as a feather compared.

i bought a gtr exedy clutch is thats and good

  • 2 weeks later...
  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 weeks later...
how do you know if a GTS4 is a S1 or S2? Also do they use the exact same drivetrain as an r33GTR, gearbox and diff?? Also would an rb25neo mate easily in the r33 chasis.

S1-(1993 - 1995) S2-(1996 - 1998) S2 would have the following : it would have different rear wing different, front ba,r different steering wheel, have passenger airbag, different seats i think its just really obvious.

Chassis number would be ERN33 on a GTS-4, you would see a transfer case in the engine bay to the left of it ( on the drivers side) right down under the engine

all specs can be looked at here

http://en.wikipedia.org/wiki/ATTESA (look for ATTESA E-TS system)

ATTESA E-TS system is used in the following models:

* R32 and R33 (1989-1997) GTS4 Skyline

* GT-R - 1989–2003

* Nissan Stagea

* A31 Cefiro

* Infiniti G35x/Nissan Skyline (V35 & V36)

* Infiniti M

* Infiniti FX

* Infiniti EX35 (with Active Brake Limited Split for side-to-side torque split, as needed)

* Nissan Fuga (Known as Infiniti M in export markets)

Edited by niiko101

how come my cluster and another r33 cluster is different the other one has slip light and A-LSD light in the middle of the rev counter and mine doesn't could this be due to cluster change or mine just doesn't come with it.

post-69895-1267600362_thumb.jpg

post-69895-1267600390_thumb.jpg

Edited by niiko101
You must have had your dash replaced, maybe with a lower k one?

Mine has a Slip light and a 4WD light. They both come on with ignition but I've never had the 4WD light up, only the slip.

if i got a proper gts-4 cluster how would i go about wiring up the slip and awd lights?

Edited by niiko101

the plugs on the back of the dash should both be the same so it should just be a case of unplug 1 dash and plug in the other. doubt there will be any need to touch any wiring as it should just be 1 or 2 big plugs (can't remember if it's 1 oe 2 plugs)

the plugs on the back of the dash should both be the same so it should just be a case of unplug 1 dash and plug in the other. doubt there will be any need to touch any wiring as it should just be 1 or 2 big plugs (can't remember if it's 1 oe 2 plugs)

The first picture is of an automatic gts-4, dont ask me why but the automatic gts-4 has a A-LSD light (As you can see in an owners manual for r33's) where as the manual skyline has a 4WD light instead of a A-LSD light, they are the same thing and they still have a A-LSD in the rear wherther it be auto or manual transmition......

Also that picture says the orange warning light is transmition well thats bullshit because its a engine warning light so dont believe that,

R33 GTS4 CLUSTER SERIES 1 AND 1.5

(right side of cluster) The 2 ontop you should have a seat belt reminder light (i dont think this works with compliance seatbelts), engine warning light,

Then the 3 below are, oil pressure warning light, exhuast warning light and battery warning light.

(left side of cluster) The 2 ontop are, door ajar, SRS air bag warning light

Then the 3 below are Low fuel warning light, ABS warning light, Brake warning light (used for handbrake but also reads when your low and brake fluid)

Then you should have 5 gauges, following from left - right

Water tempature, Fuel , Speedometer, Tachometer, Oil pressure

So far thats a GTS cluster, the last two things are a GTS4 thing and its SLIP and 4WD inbetween the Tachometer

Judging the second picture is yours, the cluster is a GTS one. It will work fine in a GTS-4 because its got a few pins missing that the GTS-4 cluster uses for the SLIP and 4WD lights. There for the 3 plugs on the back plug in as normal but the extra pins on the plugs for the GTS-4 for your SLIP and 4WD lights have nothing too do.

Has anyone ever seen there SRS, Fuel or seat belt lights in the working? i cant get any of them up when i have igntion on and am suspection the seat belt one wont work......but fuel never comes on when im low and just have never seen the SRS one and im not game too make that one show :D

The first picture is of an automatic gts-4, dont ask me why but the automatic gts-4 has a A-LSD light (As you can see in an owners manual for r33's) where as the manual skyline has a 4WD light instead of a A-LSD light, they are the same thing and they still have a A-LSD in the rear wherther it be auto or manual transmition......

Also that picture says the orange warning light is transmition well thats bullshit because its a engine warning light so dont believe that,

R33 GTS4 CLUSTER SERIES 1 AND 1.5

(right side of cluster) The 2 ontop you should have a seat belt reminder light (i dont think this works with compliance seatbelts), engine warning light,

Then the 3 below are, oil pressure warning light, exhuast warning light and battery warning light.

(left side of cluster) The 2 ontop are, door ajar, SRS air bag warning light

Then the 3 below are Low fuel warning light, ABS warning light, Brake warning light (used for handbrake but also reads when your low and brake fluid)

Then you should have 5 gauges, following from left - right

Water tempature, Fuel , Speedometer, Tachometer, Oil pressure

So far thats a GTS cluster, the last two things are a GTS4 thing and its SLIP and 4WD inbetween the Tachometer

Judging the second picture is yours, the cluster is a GTS one. It will work fine in a GTS-4 because its got a few pins missing that the GTS-4 cluster uses for the SLIP and 4WD lights. There for the 3 plugs on the back plug in as normal but the extra pins on the plugs for the GTS-4 for your SLIP and 4WD lights have nothing too do.

Has anyone ever seen there SRS, Fuel or seat belt lights in the working? i cant get any of them up when i have igntion on and am suspection the seat belt one wont work......but fuel never comes on when im low and just have never seen the SRS one and im not game too make that one show :D

thanks for that, lol nah i have never seen the fuel or srs one come on ither, my seat belt one works tho

Edited by niiko101
  • 2 weeks later...
different car i know, but my SRS light comes on in my pulsar everytime i start the car. can't remember if it did in my 33 or not, been too long since i owned it
'

only does it for me on start up

Edited by niiko101

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...