Jump to content
SAU Community

Recommended Posts

No probs Alan,

If you are able to order directly through them let me know. I want a set of '4 VALVE DOHC RS' stickers and a certain tuning book they have in stock.

The other option is going through a 3rd party importer like Jesse Streeter, but you have to pay extra commisions and postage. Stickers alone were quoted at $100 total through Mr Streeter.

Link to comment
https://www.sau.com.au/forums/topic/304349-can-anyone-help/#findComment-5040464
Share on other sites

Does anyone know where i could get a complete rubber kit for an MR30 sedan, without trying to find a kit from japan?

doing a bare matal respray and wanna replace the rubbers while im at it.

Cheers Alan

try a good Nissan Dealer near you and good luck i'm not thinking it will be cheap.

try and salvage all you seals when pulling them off

i've heard of seal kits for even some aussie delivered vehicles costing close to a couple of grand i think.

always look after your runbbers! :ph34r:

Link to comment
https://www.sau.com.au/forums/topic/304349-can-anyone-help/#findComment-5040773
Share on other sites

yeah thanks. all the rubbers are in good nic.. but have done a few complete rebuilds before and have replaced all the rubbers they didnt cost a lot ( but have never done an old jap car before either!!) I think it will be a case of take the old ones out as carefully as possiable!

Thanks Alan

Link to comment
https://www.sau.com.au/forums/topic/304349-can-anyone-help/#findComment-5041007
Share on other sites

yeah thanks. all the rubbers are in good nic.. but have done a few complete rebuilds before and have replaced all the rubbers they didnt cost a lot ( but have never done an old jap car before either!!) I think it will be a case of take the old ones out as carefully as possiable!

Thanks Alan

good idea.

If you can get your hands on "Steptone vinyl rejuvenator" (usually in a bulk container) start rubbing it in now - this stuff is the bomb and can turn even the most faded bumper into a brand new looking one in a couple of weeks.

don't use armor all or any cheap shit as it brings moisture to the top to make it look shiny for a while but will eventually dry it out which you should know is BAD

everyone take note!

I have used this for every car i have owned and it has done wonders for keeping the R30 that i just sold looking new

http://www.septone.com.au/detail.asp?item_...&page_num=1

Link to comment
https://www.sau.com.au/forums/topic/304349-can-anyone-help/#findComment-5043033
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...