Jump to content
SAU Community

Recommended Posts

Hi all looking to buy an GTR R32 as it's the look i like most out of the GTR'S just trying to do research first before seriously taking the next step and buying one, power wise i'm not really wanting to go more than a better fmic, exhaust, and a bit more boost maybe a little large huffers i do have a motec m48 not sure at this stage if that is worth keeping it for the GTR?? as a lot of guys seem to use power fc's? and since the R32 is a lot cheaper these days makes it a good time to find what i'm looking for and at a decent price.

so any do's and don'ts on what i should be looking out for in the R32 GTR i've read that the pre 92 model had issues with the oil pump which was rectified in post 92 models also i like the fact that R32's can be switched from awd to rear wheel drive by replacing the fuse with a switch, just a couple of things i've read so far so any more help on buying a GTR would be much appreciated.

Also what i would like to know is what type of internals from factory does the RB26 in the R32 GTR come with ie: forged rods? forged slugs? ect.. is there a book on the GTR with such info? and most importantly are the five speed gearbox much stronger than a WRX one as the wrx gearbox really lets it down once you up the power somewhat.

PS: only looking for a reliable daily driver with about 260-280kw atw

regards wayne

Link to comment
https://www.sau.com.au/forums/topic/305046-beginners-info-needed/
Share on other sites

People will say look for a post 89, 90, 91, etc.

Basically the newer the model the better the condition should be.

Not totally true.

I've seen 94 examples that looks more shocking than the first bunch that came out in 89.

Before I got my R32 GTR I avoided 89 models because being the first years I thought they may have some initial teething problems as with any first year models. However, if there was a problem then most if it should have been already rectified by their original owners anyway.

That said, getting a latter model would usually be better.

the skyline gearbox is bulletproof in comparison to the wrx gearbox

you wont have any issues with gearbox even with abuse

make sure you have some spare $ on the side in the case of other issues, gtr's can be costly

When you think you've figured out how much it will cost to fix any issues you've found, add approximately 30-500% for all the other unknowns and remember you pay the GTR tax on all parts.

They're not a cheap car to own, even if you do all of the work yourself.

On that note, I love every single minute I spend in mine. Well worth it.

Edited by Bozz
When you think you've figured out how much it will cost to fix any issues you've found, add approximately 30-500% for all the other unknowns and remember you pay the GTR tax on all parts.

They're not a cheap car to own, even if you do all of the work yourself.

On that note, I love every single minute I spend in mine. Well worth it.

Yeah i figured that as my last car was a jap legacy import, genuine parts were at crazy prices, but cars are our passion and i dont know anyone who finds there passions cheap, besides you only live once.

PS: i hear ya about loving every minute in your ride i'd say thats passion wright there :D

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...