Jump to content
SAU Community

Dyno Result

GTB055

By GTB055,
in General Automotive Discussion

 Share

Recommended Posts

GTB055 Enthusiast

GTB055

Posted
Posted

I was quite happy with 210.3 kw at the rear wheel on 1.05 Bar. But looking at the graph and comparing with other SAU results. I notice that my boost kick in at 95 KPH, while other people start at 60-70 KPH??? Also is it normal that the turbo kick in at 3500 rpm??? Thanks.

Mod:

-----

FMIC

Apexi power FC

Apexi AVC-R

standard turbo

3 inch exhaust (straight to the turbo)

Link to comment
https://www.sau.com.au/forums/topic/30546-dyno-result/
Share on other sites
kjb_r33 Experienced

kjb_r33

Posted
Posted

wasnt first if you hit 95 k's.

As far as power goes it makes no difference which gear its in, that would only make a difference to the torque reading, which has to be compensated for by keying in the ratio between engine rpm and TOTAL ratios. (gearbox and final drive)

Link to comment
https://www.sau.com.au/forums/topic/30546-dyno-result/#findComment-619252
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Roy
      A Boy's Love For His Rb20

      By Roy · Posted

      Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • GTSBoy
      Wheel refurb?

      By GTSBoy · Posted

      Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...