Jump to content
SAU Community

Recommended Posts

doubt hitech will run again, waste of $20 as a spectator imo

Atleast you made the effort to support it :) I destroyed a new set of 17s with some lazy burnouts :D , Import scene cry out for there own events n clowns dont show and support it :domokun:

Sounds like it should do better than a high 11?

Went 10.92 n 10.95 with R comps on it and passenger and 70hp less :)

it's already ran 10.9

When you passed me 1/2 track gate screaming i thought you be into the 10 aswell

Atleast you made the effort to support it :thumbsup: I destroyed a new set of 17s with some lazy burnouts :yes: , Import scene cry out for there own events n clowns dont show and support it :blush:

Yeah im heaing ya, unfortunetly i only fixed 4wd on my gtr on wednesday night.. otherwise i would have had it there!!

you got a cage? or just lucky to be allowed back after running 10s?

it's already ran 10.9

Im still pissed at you Adz!

3 cars i went to see, my own fault for not getting there until elims. sounds like qualifying was where the fun was at.

Boogas rx2 = dead clutch

Big O RX3 = ran 10s in qualifying.... no more runs

AD4M evo = dead clutch.

Yeah im heaing ya, unfortunetly i only fixed 4wd on my gtr on wednesday night.. otherwise i would have had it there!!

you got a cage? or just lucky to be allowed back after running 10s?

Im still pissed at you Adz!

3 cars i went to see, my own fault for not getting there until elims. sounds like qualifying was where the fun was at.

Boogas rx2 = dead clutch

Big O RX3 = ran 10s in qualifying.... no more runs

AD4M evo = dead clutch.

Yes it has 6 point cage with side intrusion bars . GTR ran the 10s while doing Fabcar 1 day rally , NOT run under ANDRA insurance so dont need to meet there requirements ..

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...