Jump to content
SAU Community

Recommended Posts

selling my rb26 race head, i changed direction with my engine, after experienceing electrical problems with the gtr putting it in a workshop for a very long time and after alot of thinking deciding to change a few things, so hence the sale. i had a new head built for my new setup.

seen about 1500-2000km driving and dyno runs

was part of a setup that made 565awkw @ 21psi on pump fuel, so the head is good for it and is really really strong.

looking for around $7500, which is merely half of what it cost to build! needs to be sold asap to fund new setup.

Parts list:

Ferrea 1mm oversize stainless valves

Aftermarket valve guides

Apexi V-Max SPL springs, retainers and buckets

Apexi V-Max SPL 280 deg 11.5mm lift cams

Tomei camshaft stud kit

Trust cam gears

New stem seals

whats been done to the head:

Ported intake + exhaust runners

Profile guides

Polished + cc'd chambers

Unshroud valves in chamber

Flow benched and runner flow equalised

Steam hole modifications/water gallery modifications

Clearanced for high lift cams

Drilled for 1/2inch head studs

Flow figures:

Lift Int Exh

0.05 51.9 46.4

0.1 100.4 94.5

0.15 147.2 134.8

0.2 186 167.5

0.25 221.3 197.2

0.3 252.4 219.5

0.35 277.5 229.7

0.4 292.9 236.8

0.45 304.7 240.8

0.5 309.2 241.8

heres a few pics before the head was fitted up..

post-23724-1264859137_thumb.jpg

post-23724-1264859163_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/306140-rb26-race-head/
Share on other sites

  • 2 weeks later...

hey its only a 3L haha i built a new head because we did specific porting with it after some guidance from o/s regarding circuit work coz thats where i wanna focus most of the car, but its all goin together this week with a T51R KAI, so prob around 500AWKW but really responsive, torquey and a very nice curve. hows ur car goin, my bro saw i i think and tried to tell me to put an auto in it haha

Link to comment
https://www.sau.com.au/forums/topic/306140-rb26-race-head/#findComment-5110161
Share on other sites

Are you using that spare os rb30 you have or a nitto crank and rods from croydon?

ye im using the OS RB30 i had here. this car is doing my head in! haha 3 years now

hey sorry i know its a little off topic..

you dont have any rb30 cranks lying about?? i need one to keep my build going.

no sorry. i do have a mad head for sale haha

Link to comment
https://www.sau.com.au/forums/topic/306140-rb26-race-head/#findComment-5111143
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...