Jump to content
SAU Community

Recommended Posts

hey guys and girls.

i am planing on drifting my 180 for the first time on the next drift practise in feb.

would like some idea on what i should bring and how much of it

also how much is it going to cost me, i will be going to all the drift practises throughout the year

thanks

Gordon

Link to comment
https://www.sau.com.au/forums/topic/306154-first-time-drifting/
Share on other sites

Bring atleast 2x pairs of tyres...and have a third pair to drive to/from the event on.

Don't even think about trying to get home on a pair you've used.

Can of fuel, if you're gonna be hammering it with rich tune.

Make sure you're all set up to pass scrutineering:

Fire Extinguisher (floor mounted, passenger side of the gearbox)

No loose shit inside the car.

Long sleeve shirt and pants, enclosed footwear

Decent tread on front tyres

Battery tied down, marked by sticker

Tow points marked by sticker

Assuming you have your membership and CAMS license, you only need to pay for entry.

http://www.driftwa.com.au/

hey guys and girls.

i am planing on drifting my 180 for the first time on the next drift practise in feb.

would like some idea on what i should bring and how much of it

also how much is it going to cost me, i will be going to all the drift practises throughout the year

thanks

Gordon

if its your 1st time out then will send you out the back of the track to do some practice work (around cones etc, till you feel your ready to head out onto the track).

Come with a full tank of fuel and that will last you for the night (there are afew fuel stops about 5-10mins from the track). one set of rims (rears only) should be plenty for your 1st time, i say you wouldn't even need to change them at the end of the time (depends on what size you plan to run)

best bet is just have your drift rims and then your normal drive home rims.

cost

$60 for cams (once a year, Only need lvl 2 non-speed)

$250 for wascc license (once a year)

$60 for the practice

$40 for Fire Extinguisher (can get from supercheap etc)

Go Gear have the tow and battery stickers ($10 or $15)

And the main thing is just to have fun =) and remember you don't have to go out onto the track unless you feel you are ready!

hopefully will have my car ready for the feb prac

so i have to bring my own jack. do i have to worry about chaining up my wheels so no one takes off with them? i got drift tek rims on atm will be using 4x stock wheels for the rear on the day. wouldnt hurt to bring some tools?

Will need your own jack and tools, but if you're without something, fellow drifters are always friendly enough to help you out.

Shouldn't need to worry about chaining up your wheels and whatnot, some people do, but again...drift community are pretty cool blokes.

Hey man,

If you dont have a jack dont worry you can park uo near me and excentrix and use my crap if you like,

You dont need a fire extinguisher for practice, just tow stickers and battery triangles, and even then they dont really worry about it much.

You wont chew a full set of tyres in your first prac unless your making big power.

Bring a set of skid rims if you like and we can swap them before you go out.

If you have never had cams or wascc before then total cost is about ~430 off the top of my head which will include your entry for the night,

Come early as it will take a while to sign up/change tyres/talk crap and people have been getting irritated about late starts recently.

Long shirt and pants and enclosed shoes.

Need a helmet.

You wont even use a half tank of petrol unless your again making big power, im lucky to use a quarter of a tank at most.

Set your tyre pressures a bit higher than usual, i run mine at 40 psi all round.

Thats about it. Send me a pm if you like and you can meet me and thomas before we head down to the track I live just down the road.

Regards,

Greg

Gordon if i am down there (finger cross the car will be ready), i am more than happy to help you out (think i meet you maybe once at beyond custom). I will have a jack and plenty of tools. just come down and say hi my name is Michael and i have the grey r33 (evl r33)

  • 1 month later...
im worried my exhaust is going to be too loud. i just read on drift wa forums that they dont like overly loud

trust me you won't have a problem, my mates na 4age was f**king loud (just straight pipe) and they had no issue with it. plenty of guys running ext gate too with no issues

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...