Jump to content
SAU Community

Rb26 Carrillo Rods

GTR STI
 Share

Recommended Posts

GTR STI Community Regular

GTR STI

Posted
Posted

I have 2 sets of RB26 rods for sale.

"CARRILLO" CNC machined from 4340 chome moly forgings. (A lightweight rod)

At the factory they are heat treated, then magnaflux inspected and hardness checked, then machined to final size. Each set of rods is balanced and then shot peened to achieve the ultimate in strength and fatigue properties. The rod bolts are the multiphase SPS-CARR units. These rod bolts have a design tensile strength of 285,000 PSI and are designed to be a non-replacement type fastener. These are low kilometer rods with a replacement value of $3600 for sale at $1900. (Available now)

RB26 std. rods from a 16000km R33 GTR v-spec. $600. (Available in Feb.)

Phillip

[email protected]

0409573124

Link to comment
https://www.sau.com.au/forums/topic/30679-rb26-carrillo-rods/
Share on other sites
  • 2 months later...
Merli Grand Master

Merli

Posted
Posted

If the Carrillos are 21mm gudgeon pin size (standard), then I'll give you $1000 for them.

Question: If the rod bolts are a "non-replacement type fastener" does that mean that they're useless to the buyer or did you buy new ones to sell with the rods?

edit: oh, and why do you have "Carrillo" in inverted commas? Are they genuine Carrillos or not?

GTR STI Community Regular

GTR STI

Posted
  • Author
Posted

non-replacement type fastener......last a life time....don't have to replace at every rebuild.

285,000psi bolts....ARP from memory is only 100,000psi.

Gen. Carrillo.....Carrillo make the rods for HKS...but the Carrillo are shotpeen prior to machining....Carrillo, HKS, Tomie are all H-beam, most others are only I-beam.

You get what you pay for.

$1500 is the best I am willing to do.

May take trade however......clutch, cam kit, etc.

Merli Grand Master

Merli

Posted
Posted

I assume that all the rods are in perfect condition? No warping or damage?

Have you weighted all the rods? Are they still all still balanced?

Have you attacked them with verniers and made sure there is no stretching around the either end (big end and gudgeon pin end)?

It's a little hard to do this with second hand parts considering we're in different states and I can't get my hands on them to measure them...

Would you be able to take close ups of all the rods?

Why did you remove them from your engine?

email me: andrew at andrewho dot com

Sydneykid Grand Master

Sydneykid

Posted
Posted

It has been my experience that Carrillo make the best conrods, bar none. I have never had a Carrillo rod fail and we have used them in some extreme stuff. If I was building a strong RB26 or RB25, these are the rods I would choose.

For the price GTR STI is selling them you could not buy better. Hi Merli, jump on a cheap Virgin and go and look at them, it's worth it.

Merli Grand Master

Merli

Posted
Posted

Hey SK...

Thanks for confirming what I thought... I knew that Carrillos are excellent rods, and definitely WELL beyond the power levels I'm aiming for, but it's always good to have overheads built in :(

Unfortunately I don't have time to fly upto Brissy anytime soon...

Phillip: Are you willing to send them to me, pending my getting them checked out and measured? If they're all fine, I'll take them for $1500. I can give Chris (doughboy) the money to hold as an escrow if you feel more comfortable with that, but rest assured I'm good for it :( I'm not about to rip anybody off over some conrods :)

Thanks again Sydneykid.

Let me know what you think Phillip,

Andrew.

Merli Grand Master

Merli

Posted
Posted

Shouldn't it really go by the timestamp of the post? If I had known you'd check your PM's first, I wouldn't have bothered with posting in your actual For Sale Thread, which is the correct forum for discussion is it not?

If Sebaz sent his PM first, then I have no qualms, but if my post at 11:22pm yesterday was first, that's quite unfair.

GTR STI Community Regular

GTR STI

Posted
  • Author
Posted

Sorry Merli,

I'm as fair as they come.

Working up in Wepia at the moment....two people had rang my home in Brisbane...prior to your post.

But by the sounds of it SEBAZ may have a set of other rods for sale soon.

Give him a PM.

have fun....it's alway raining here.

Phil

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...