Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

actually i had a guy do it for me, but there was nothing difficult about it. Just pull out the rectangular covers on the side, unscrew the first bolts you see inside and things just slide off so you can pull things apart from the inside (steering wheel, airbag harness etc). The airbag itself needs to be taken out slowly that's all.

I know I've been vague, sorry...I remember watching the guy do it, n i thought, I could've done that bit myself. The hard part is getting all the other crap out from inside, and reaching the bolt that the boss kit will eventually go onto.

hmmm make sure you pull the plastic rectangular cover off from underneath the steering wheel. Then undo the plug that you see under there, that will disconnect the airbag.

remove 2 side screws as covered by Nrage33, you will need a tamperproof T50 driver. If you can't get a tamperproof, use a screwdriver to break the "point" out of each of the bolts then use a normal T50. Everything will slide out then...

butthead , before u do it find the airbag fuse and take it out , if u cant find that disconect the battery and take care when handling the air bag always hold it away from ur head .

As wrxhoon said,,,,either remove the fuse or disconnected the battery. I would have you dis-connect the battery myself. After that you can do what you like with it. It will not explode without voltage and thats a FACT. It's an electronic exploding device that is as lame as with no voltage. You will have to get someone that knows Nissan's to reset the light after you re-install it though.

Neil.

You will have to get someone that knows Nissan's to reset the light after you re-install it though.

So I can't just disconnect battery, remove standard nissan airbag steering wheel, replace with a different standard nissan airbag wheel (in much better condition) and plug the battery back in to find everything 100% ?

butthead ,

i'm not sure if u have to reset the airbag light after u reistall it as i havent removed one in a skyline before . i have done it in other cars though and it works without reseting it .neil have ever had a skyline wheel removed? ( airbag ).

always be very carefull with airbags even if they are disconected , u dont want to loose u r head .

I just took the 3 plastic covers off my wheel to take a closer look (woulda took some pics but parents borrowed my camera for the nite).

For the last 9-12mths my wheel makes a clunk sound everytime I turn it about 90-180 deg and then clunk again when I turn it back. I'm guessing something inside is loose and is just rolling around but after taking the covers off and looking inside I can't see anything that isn't joined to another part that could be loose. Also now over the last week it sounds like a spring or something is loose along with the clunk clunk sound and it sounds like the wheel is gonna fall to pieces in my hands 1 day when driving. I can get a 2nd hand good condition wheel and hopefully just straight swap it but if my current wheel just needs a bolt tightened etc then i'd much rather just tightened the bolt and get another 6mths out of the wheel (if the leather will hold up that long). Anyone got any ideas ?

From what I can see (with a torch) their is just 2 weird shaped bolts on either side and then I guess the wheel just slides off (??). Underneath I can see 2 different plugs. It looks like 1 is a cable plugging into a socket and the other is just to cables plugged directly into each other.

Which 1 of these 2 needs to be unplugged to de-activate the airbag?

benm:

have u ever taken a steering wheel out before ? once u take out the cover ( regardless were it has an airbag or not ) u have to undo the nut ( usualy around 19 - 21 mm) then u need a gear puller to pull it off ( its tapered so it will be very tight ) .when u reinstall it u have to put it in the same position as it was before otherwise when u go in a straight line the wheel will not be in centre position .this is the best way to do it . put the wheel in centre pos and the front wheels pointing straight then take the wheel off ,make sure u dont turn the shaft when taking the wheel off or while its off when u r ready to put it back u put it cenre pos again , put the nut on take it for a drive if its one tooth out pull out and turn one tooth .

when u take the cover off ( with the airbag )u'll see the wires u have to undo , airbag wires are usualy yellow .

make sure u take the fuse off or disconect the battery .

funkymonkey , yes ur right but remember when u r driving u r head is far away from the airbag and u can get a broken nose but thats the price u have to pay so u dont get seriously hurt or even die .

Just spoke to CRD in Silverwater and they told me to remove my standard nissan airbag wheel and replace it with a good condition standard nissan airbag wheel i will need a boss kit worth $150 and thats all they can supply (It's illegal for them to change airbag wheels).

I'm guessing Nissan will be the only workshop that can replace my wheel and if thats the case it will be cheaper for me to buy an aftermarket Momo wheel + Boss kit (illegal modification) and have that fitted than to just put another Nissan airbag wheel on.

Not happy Jan !!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...